4.2 Operation Procedures
Remove the Lid with the Filler Cap.
First, fill the Cup with liquid products and after that, prod-
ucts with more consistency.
Do not use this blender to process dense products, like
the dessert known as "acai cream".
Cut the product in small pieces approximately 3.5 cm
wide, it will help to reduce the blending time particularly
with frozen products. When processing ice, it is obligatory
to add some water.
Place the Lid with the Filler Cap as described before in Items
3.4.2 and 3.4.3 and turn on the appliance.
The processing time changes for each product. Solid
products should not be processed without a liquid, because
overheating may occur and therefore damage the Cup seal.
Never turn on the Appliance when empty, because it
can cause irreparable damages.
5. CLEANING
Remove the plug from the socket before starting the
cleaning process.
The Equipment must be completely cleaned and sanitized:
- Before using it for the first time;
- Every day before closing the work shift;
- Always when it has not been in use for a long time;
- Before using after it has not been in use for a long time.
Some parts of the equipment may be removed to be
cleaned:
-Lid #01 (Pic. 01);
-Cup #02 (Pic. 01);
-Cap #10 (Pic. 01).
Do not use water jet directly on the equipment.
Wash all the components with water and neutral detergent.
- To wash the inside of the Cup, fill the Cup to half its capacity
with water and add a small dose of neutral detergent.
- Put on the lid and turn on the blender for 30 seconds.
- Remove contents and rinse the Cup.
- If necessary use a brush with handle and nylon bristles to
assist in the removal of materials impregnated in it.
Use Your QR Code Reader to access
more information regarding the cares
and attention needed when handling
stainless Steel.
6. MAINTENANCE
The maintenance must be a group of procedures that have
the objective of keeping the appliance in its best condition
4
of operation and increasing its life expectancy and safety.
* Cleaning – Check the item 5 Cleaning of this Manual.
* Electrical wiring – Check all the cables to avoid deterio-
ration and all the electrical contacts about their tightening
and corrosion
* Contacts – ON and OFF Switch, emergency switch, reset
button, eletric circuits, etc. Check the appliance so that all
the components are working correctly and that the opera-
tion is working normally
* Installation – Check the installation of your appliance ac-
cording to the item 2.1 Installation of this manual.
1 – Items to be verified and implemented monthly:
- Check the electrical installation;
- Check the outlet tension;
- Measure the operating current and compare it to the no-
minal one;
- Check all the eletrical terminal tightening of the appliance,
to avoid bad contact;
- Check the possible clearance of the shift of the electric
motor;
- Check the wiring and the electric cable to avoid its overhea-
ting, deficient isolation and mechanical breakdown.
2 - Items to be verified and implemented every 3 months:
- Check the electric components as ON/OFF switch, emer-
gency button, reset button, and eletric circuit related to
overheating, deficient isolation and mechanical breakdown.
- Check possible loosens in the bearings
- Check retainers, o´rings, v´rings and other sealing systems.
Use your QR Code Reader to access
more information regarding safety and
maintenance.
7. PROBLEMS SOLVING
PROBLEMS
- Lack of electric
power.
- The appliance
does not
- Problems in the
switch on.
electrical circuit.
- Problems in the
- Smoke or
internal and external
burnt smell.
electrical circuit.
- The appliance
switch on
but when the
- Problems with the
product is
motor.
placed it stops
or the blades
turn slowly.
- Damaged
- Failure during
cord.
transport of product.
CAUSES
SOLUTIONS
- Check if plug is
connected to its
socket and do as
explained in item
3.1 Starting.
- Call technical
assistance.
- Call technical
assistance.
- Call technical
assistance.
- Call technical
assistance.