Zircon LASERVISION QUBE System Guia De Inicio Rapido

LASERVISION
The Zircon LASERVISION ® QUBE ™
System is the fastest, most
versatile way to find level and
plumb. With the simple-to-use
modular system, magnetic QUBE ™
lasers snap to the base and to
each other creating perfect lines
and angles.
LIMITED 1 YEAR WARRANTY
Zircon Corporation, ("Zircon") warrants this product to be free from
defects in materials and workmanship for one year from the date of
purchase. Any in-warranty defective product returned to Zircon*, freight
prepaid with proof of purchase date and $5.00 to cover postage and
handling, will be repaired or replaced at Zircon's option. This warranty is
limited to the electronic circuitry and original case of the product and
specifically excludes damage caused by abuse, unreasonable use or
neglect. This warranty is in lieu of all other warranties, express or
implied, and no other representations or claims of any nature shall bind
or obligate Zircon. Any implied warranties applicable to this product are
limited to the one year period following its purchase.
IN NO EVENT WILL ZIRCON BE LIABLE FOR ANY SPECIAL, INCIDENTAL
OR CONSEQUENTIAL DAMAGES RESULTING FROM POSSESSION, USE OR
MALFUNCTION OF THIS PRODUCT.
In accordance with government regulations, you are advised that:
(i) some states do not allow limitations on how long an implied warranty
lasts and/or the exclusion or limitation of incidental or consequential
SAFETY INSTRUCTIONS
DANGER
LASER RADIATION
Avoid Direct Eye Exposure
Maximum Output Power < 5 mW @ 650 nm
Class IIIa Laser Product
This product complies with standards
applicable to 21 CFR parts 1040.10
and 1040.11
• Do not stare directly at the laser beam.
• Do not project the laser beam in a manner that would cause others to look into the beam.
• Do not use any other optical devices in conjunction with the laser tool.
• Do not operate near children.
• Always turn off the laser tool when not in use.
SPECIFICATIONS
• Self-levels within ± 5 degrees
• Red laser diode: 650 nm Class IIIa
• Accuracy: typically within 1 ⁄ in. at 50 ft. (6 mm at 15 m)
4
INSTALLING THE BATTERIES
Unscrew bottom cover
1
counter-clockwise and
lift. Place 3 C batteries
in the compartment,
matching (+) and (-)
terminals from
battery to case.
2 Replace battery door and
rotate shut. Batteries will
last approximately 2 years
under normal conditions.
OPERATION
Place unit on a stable, flat surface
3
and press the Power Button.
Level Indicator light will flash
while scanning for level, and shine solid
when the platform is level. If the unit is
unstable or at an incline of more than 5
degrees auto level cannot function and
the Out of Auto Level Range Indicator
will shine red. Power down and
reposition the unit.
® QUBE ™ System
Power Button and
QUBE
Indicator Panel
damages, so the above limitations and/or exclusions may not apply to
you, and further (ii) this warranty gives you specific legal rights and
you may also have other rights which vary from state to state.
Return product freight prepaid with proof of purchase date (dated
sales receipt) and $5.00 to cover postage and handling, to:
Zircon Corporation
*Attn: Returns Department
1600 Dell Avenue, Unit K
Campbell, CA 95008-6992 USA
Be sure to include your name and return address. Out of warranty
service and repair, where proof of purchase is not provided, shall be
returned with repairs charged C.O.D. Allow 4 to 6 weeks for delivery.
Customer Service: 1-800-245-9265 or 1-408-963-4550
E-mail: info@zircon.com
Patents Pending
©2004 Zircon Corporation • P/N 59664 Rev A 07/04
Warning: read and understand all
instructions prior to operating this
laser tool.
Warning: laser light. Avoid direct eye
exposure. Do not look into beam.
• Operating temp: 20° –110°F (-7° – 43°C)
• Batteries: 3 C 1.5 volt alkaline
–
+
+
+
Power Button
Low Battery Indicator
Out of Auto Level Range Indicator
Place QUBE
4
plate. Attach QUBE
power strip.
™ Contact Plate
Laser will turn on
5
automatically when
full contact is made.
Power Strip
Rotate or flip QUBE
6
to desired position.
Battery Cover
Warning
Disconnect when not in
use to avoid eye contact.
QUBE ™
7
bination for many possible effects.
QUBE ™
together to form perfect angles.
180°
SYSTEM APPLICATIONS
Decks
Kitchen/Bath
Storage
C
3X
+
ACCESSORIES
Scan/Level Indicator
Jamb Pole with
Tripod Legs
™ laser on contact
™ cable to
™ laser
lasers can be used in com-
lasers magnetically snap
90°
Decorating
Molding
Tile
QUBE ™ Laser Line
QUBE ™ Laser Dot
90°
90°
Floor to Ceiling
Remodeling
Ceiling Lights
Bracket with Multiposition Clamp