Descargar Imprimir esta página

Publicidad

Enlaces rápidos

Issued / Herausgegeben / Publicado / Publication 11/2000
Instruction Leaflet
Bedienungsanleitung
Hojas de instrucciones
Feuille d'instructions
Foglio d'instruzioni
Sensors contain a positive temperature co-efficient (PTC), platinum
resistance temperature sensor. The temperature/resistance characteristic is
linear and is given below:
Temp.
R value
Temp.
(°C)
(Ω)
(°C)
-20
92.16
30
-10
96.09
40
0
100.00
50
10
103.90
60
20
107.79
70
The resistance (and therefore temperature) of the sensor can be taken
directly to a controller. For this application, two wires are provided (three
wires on pipe strap-on sensor - RS Stock no. 813-890). If 3 or 4 wire
resistance compensation is required, double up the cable connections to the
sensor terminals. Alternatively, sensors can be used in conjuction with
current transmitters, which fit into the sensor enclosure to provide a 4-20mA,
loop-powered signal (-10/+40°C): RS stock no. 376-1483, -10/+110°C: RS
stock no. 376-1506.
Physical installation
RS stock no.
376-1477 Space air temp.
Affix back plate to wall or back-box in a
location which excludes drafts and direct
sunlight. Use terminal supplied for connecting
to sensor
813-862 Duct air temp.
Drill 6.2mm hole in duct and insert probe. Mark
off fixing holes, remove and drill. Fix securely to
duct. Use M20 cable entry for cable gland or
conduit. Do not install until the system has
been started up and run for some hours, in
order to remove contaminants. Avoid high
vibration areas.
813-878 Outside air temp. Use sensor as template for fixing holes. Use
gland or threaded conduit as above.
813-884 Immersion temp. For liquid temperature measurement, use in
conjunction with pocket (brass: RS stock no.
813-941, stainless: RS stock no. 813-957). Fix
pocket into 1/2" BSPT pipe boss and insert
sensor into pocket, ensuring that the end butts
up against the end of the pocket. Tighten
pocket screw against probe until firmly
secured.
813-890 Pipe strap temp.
Fix sensor lug to pipe using stainless steel
strap provided.
RS Stock No.
376-1477, 813-862, 813-878
813-884 & 813-890
R value
Temp.
(Ω)
(°C)
111.67
80
115.54
90
119.40
100
123.24
110
127.07
PT100 Temperature Sensors
PT100 Temperatursensoren
Sensores de temperatura PT100
Sondes de température PT100
Sensore della Temperatura PT100
Electrical installation
1. Make electrical connections to sensor only after all other electrical
installation and test has been completed.
2. It is recommended that screened cable be used on all installation, with
screens being earthed at the controller. Signal cables should not be laid
in close proximity to power cables or other sources of interference.
3. Connections to the sensing element can be two, three or four wire.
Sensor resistance is measured across any red/white pair.
4. Note:
Thermistors exposed to excess voltage and/or current will
usually fail closed circuit. Units failing in this way will not be
R value
repaired or replaced under warranty.
(Ω)
130.89
Technical specification
134.70
PT100 accuracy__________________________: As DIN IEC 751 Class A
138.50
Self heating effect
142.29
Recommended
power rating __________________________________________: <1mW
Operating range #
Protection rating
Enclosure material: All plastic enclosures
# In all cases, ABS enclosures should not be exposed to temperatures
outside the range - 10/+80°C.
* Sensor elements will degrade over time when exposed to high
humidities.
® IP
rating dependent upon the use of suitable M20 cable gland,
(supplied).
RS Components shall not be liable for any liability or loss of any nature (howsoever
caused and whether or not due to RS Components' negligence) which may result
from the use of any information provided in RS technical literature.
Die Sensoren sind mit einer Meßsonde des Typs PTC (Positiver
Temperaturkoeffizient) ausgerüstet. Die Temperatur/Widerstands-Kennlinie
ist linear, und zwar wie folgt:
Temp.
Widerstand
(°C)
-20
-10
0
100,00
10
103,90
20
107,79
__________________________________: 0.2°C/mW
RS stock no
376-1477
Space air temp.
813-862
Duct air temp.
813-878
Outside air temp.
813-884
Immersion temp.
813-890
Pipe strap temp.
376-1477
IP20
813-862, 878, 884, 890
IP67®
: Flame retardant ABS
376-1477, 813-862, 813-878
Temp.
Widerstand
(Ω)
(°C)
(Ω)
92,16
30
111,67
96,09
40
115,54
50
119,40
60
123,24
70
127,07
V9733
-10/+60°C
-10/+80°C
0-90%RH*
-10/+80°C
0-100%RH
-10/+80°C
0-100%RH
-10/+110°C
0-100%RH
RS Best-Nr.
813-884, 813-890
Temp. Widerstand
(°C)
(Ω)
80
130,89
90
134,70
100
138,50
110
142,29

Publicidad

loading

Resumen de contenidos para RS PT100

  • Página 1 For this application, two wires are provided (three Operating range # 376-1477 Space air temp. -10/+60°C wires on pipe strap-on sensor - RS Stock no. 813-890). If 3 or 4 wire 813-862 Duct air temp. -10/+80°C 0-90%RH*...
  • Página 2 (tres cables en el caso del sensor de sujeción a tuberías - n.º de Befestigungslöcher benutzen. stock RS 813-890). Si se precisa una resistencia de 3 ó 4 cables, duplique Kabelstutzen oder -schutzrohr wie oben las conexiones de cable a los bornes del sensor. Otra alternativa consiste verwenden.
  • Página 3 à un contrôleur. Deux fils sont fournis pour cette application (trois 813-862 Température air conduite -10/+80°C 0-90 % HR* fils pour les sondes montée sur tuyau, référence stock RS 813-890). Si une 813-878 Température air extérieur -10/+80°C 0-100 % HR* compensation de la résistance sur 3 ou 4 fils est nécessaire, doublez le...
  • Página 4 3. Le connessioni all'elemento sensore possono essere costituite da due, tre o quattro cavi. La resistenza del sensore è misurata mediante la La société RS Components n’est pas responsable des dettes ou pertes de quelle que coppia di colore rosso/bianco.

Este manual también es adecuado para:

V9733