Metra Electronics XSVI-6523-NAV Manual Del Usuario

XSVI-6523-NAV
Dodge accessory and NAV output
CAN Interface 2013-up
XSVI-6523-NAV
• Provides accessory (12 volt 10 amp)
• Retains R.A.P. (retained accessory power)
• Used in non-amplified systems or when replacing amplified system
*Fiat 500L only: For use in both amplified and non-amplified systems
• Provides NAV outputs (parking brake, reverse, and V.S.S.)
• Prewired ASWC-1 harness included (ASWC-1 not included)
• Retains back-up camera (if through the OE radio)
• Retains the use of the 3.5mm AUX jack
• High level speaker input
• USB updatable
Note: XSVI-6523-NAV does not retain amplified sound system.
APPLICATIONS
DODGE
Dart (small screen option) 2013-up
FIAT
500L 2014-up
Wiring the XSVI-6523-NAV
• Connect the Yellow wire to the radio's 12-volt battery or memory wire.
• Connect the Black wire to the radio's ground wire.
• Connect the Red wire to the ignition wire of the aftermarket radio.
• Connect the Orange/White wire to the illumination wire of the aftermarket radio.
If the aftermarket radio has no illumination wire, tape off the Orange/White wire.
• For Fiat 500L only, connect the Blue/White wire to the amp turn on wire of the radio.
• Connect the White wire to the left front positive speaker output of the aftermarket radio.
• Connect the White/Black wire to the left front negative speaker output of
the aftermarket radio.
1-800-221-0932
REV. 12/19/13 © COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORATION
RAM
1500, 2500, 3500 (small screen option)
2013-up
Chassis Cab 3500, 4500, 5500
(small screen option) 2013-up
metraonline.com
XSVI-6523-NAV
• Connect the Gray wire to the right front positive speaker output of the
aftermarket radio.
• Connect the Gray/Black wire to the right front negative speaker output of
the aftermarket radio.
• Connect the Green wire to the radio's left rear positive speaker output.
• Connect the Green/Black wire to the radio's left rear negative speaker output.
• Connect the Purple wire to the radio's right rear positive speaker output.
• Connect the Purple/Black wire to the radio's right rear negative speaker output.
• Connect the Light Green wire to the parking brake wire of the
aftermarket navigation radio.
• Connect the Blue/Pink wire to the VSS or speed sense wire of the
aftermarket navigation radio.
• Connect the Green/Purple wire to the reverse wire of the aftermarket navigation radio.
RCA Connections
• Connect the Yellow RCA to the video in of the aftermarket radio to retain the
OE back up camera (if equipped).
• Connect the White and Red RCA to the aux in of the aftermarket radio to retain
the OE 3.5mm jack (if equipped).
Initialize the XSVI interface
With all connections made and harnesses connected to the vehicle, turn the ignition key to
the ON position for 30-seconds, then turn the key OFF, then ON again to test the radio.
ASWC-1 (if installing)
After the XSVI is initialized, plug in the ASWC-1 into the 12-pin harness of the
XSVI-6523-NAV and refer to the ASWC-1 instructions.
K P
NOWLEDGE IS OWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
Metra recommends MECP
certifi ed technicians
1-800-221-0932
REV. 12/19/13 © COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORATION
Caution: Metra recommends disconnecting the
negative battery terminal before beginning any
installation. All accessories, switches, and especially
air bag indicator lights must be plugged in before
reconnecting the battery or cycling the ignition.
Note: Refer to the instructions included with the
aftermarket radio.
metraonline.com