Correction Of Malfunctions - Bosch 3 603 B06 2 Serie Manual Del Usuario

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 28
OBJ_BUCH-420-002.book Page 19 Tuesday, August 23, 2011 12:08 PM
– Clean the nozzle 11 and the nozzle needle with diluting
agent.
From time to time, the nozzle seal 12 must also be cleaned.
– Remove the nozzle 11 and the nozzle seal 12.
If required, use a pointed object, as the nozzle seal is seat-
ed firmly to the spray gun.
– Clean the nozzle seal with diluting agent.
– Reinstall the nozzle seal in the spray gun. Pay attention that
the groove points away from the spray gun.
– Mount the nozzle onto the spray gun body and turn it to the
correct position.
– Mount the air cap 2 onto the nozzle and tighten with the un-
ion nut 3.

Correction of Malfunctions

Problem
Spray material does not cover
properly
Spray material runs off after
coating
Atomisation too course
Excessive paint mist
Spray jet pulsates
Spray material drips from the
nozzle
Bosch Power Tools
Changing the Air Filter (see figure L)
The air filter must be replaced when soiled.
– Remove the air filter cover 21.
– Change the air filter.
– Remount the air filter cover.
Material Disposal
Diluting agent and remainders of spray material must be dis-
posed of in an environmentally-friendly manner. Observe the
manufacturer's disposal information and the local regulations
for disposal of hazardous waste.
Chemicals harmful to the environment may not be disposed
of into soil, groundwater or bodies of water. Never pour
chemicals harmful to the environment into the sewerage sys-
tem!
Cause
Spraying capacity too low
Clearance to target area too large
Not enough spray material on target area,
too few spray paths sprayed over target area
Spray material too viscous
Too much spray material applied
Clearance to target area too close
Viscosity of spray material too low
Spray material applied too often over same
spot
Spraying capacity too high
Air flow too low
Nozzle 11 soiled
Too little pressure build-up in container 8
Spray material too viscous
Air filter heavily soiled
Too much spray material applied
Clearance to spray surface too large
Viscosity of spray material too low
Not enough spray material in container
Venting hole on suction tube 10 clogged
Air filter heavily soiled
Spray material too viscous
Build-up of spray material on nozzle 11 and
air cap 2
Nozzle 11 worn
Nozzle 11 loose
English | 19
Corrective Measure
Turn thumbwheel 5 in direction IIII
Reduce spray distance
Apply more spray paths over target area
Thin down the spray material by 10% again
and carry out a test-spray run
Turn thumbwheel 5 in direction I
Increase spray distance
Add original spray material
Remove spray material; reduce number of
spray paths over same spot
Turn thumbwheel 5 in direction I
Turn control knob 16 toward the right
Clean nozzle
Screw container firmly against spray gun
Thin down the spray material by 10% again
and carry out a test-spray run
Changing the Air Filter
Turn thumbwheel 5 in direction I
Reduce spray distance
Reduce air flow; turn control knob 16 toward
the left
Refill spray material
Clean suction tube and hole
Changing the Air Filter
Thin down the spray material by 10% again
and carry out a test-spray run
Clean nozzle and air cap
Replace nozzle
Tighten union nut 3
1 609 929 Y14 | (23.8.11)

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Pfs 105 e

Tabla de contenido