Craftsman CMXLHB5 Manual De Instruccion

LED RECHARGEABLE HEADLAMP
INSTRUCTION MANUAL
ZOOM/FOCUS SELECTION KNOB
POWER/LIGHT MODE BUTTON
MAIN LED BULB
TWO RED LED AREA LIGHTS BUILT-IN USB PLUG
SAVE THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE.
Copyright © 2020 Baccus Global LLC
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
■
Increase the separation between equipment and receiver.
■
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
■
Consult the dealer or an experienced radio/TV technician for help.
■
Changes or modifications not approved by the party responsible for compliance could void user' s authority to operate the equipment.
SAFETY GUIDELINES / DEFINITIONS
DANGER:
Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
WARNING:
Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION:
Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
CAUTION:
Used without the safety alert symbol indicates potentially hazardous situation which, if not avoided, may result in property damage.
RISK OF UNSAFE OPERATION.
When using tools or equipment, basic safety precautions should always be followed to reduce the risk of personal injury.
Improper operation, maintenance or modification of tools or equipment could result in serious injury and property damage. There are certain applications for which tools
and equipment are designed. Manufacturer strongly recommends that this product NOT be modified and/or used for any application other than for which it was designed.
Read and understand all warnings and operating instructions before using any tool or equipment.
READ ALL INSTRUCTIONS
WARNING:
Read all instructions before operating the LED headlamp. Failure to follow all instructions listed below may result in electric
shock, fire and/or serious injury.
IMPORTANT SAFETY INSTRUCTIONS
GENERAL SAFETY WARNINGS AND INSTRUCTIONS
WARNING –
WHEN USING THIS HEADLAMP, BASIC PRECAUTIONS SHOULD ALWAYS BE FOLLOWED, INCLUDING THE FOLLOWING:
For household use only.
■
Do not incinerate.
■
To reduce the risk of injury, close supervision is necessary when the headlamp is used near children.
■
Use only attachments recommended or sold by the manufacturer.
■
SPECIFIC SAFETY INSTRUCTIONS FOR CHARGING THIS UNIT
WARNING –
TO REDUCE THE RISK OF ELECTRIC SHOCK:
Charge indoors only.
■
Do not expose the built-in USB plug to moisture, water or any other liquid.
■
Use only the built-in USB plug supplied by the manufacturer to recharge.
■
Make sure the light is turned off before connection to a power source.
■
If an external adapter is used as a USB power source, make sure it is a Class 2 power unit.
■
The light should be turned off when charging or not in use.
■
WARNING –
TO REDUCE THE RISK OF PROPERTY DAMAGE:
Never place the light face down on any surface when lit, charging or not in use. Never store the light face down on any surface.
■
Make sure the built-in USB plug is clean and free of debris.
■
Failure to keep the battery charged will cause permanent damage and result in poor performance.
■
CMXLHB5_ManualENSP_063020.indd 1 CMXLHB5_ManualENSP_063020.indd 1
Make sure the built-in USB plug is properly inserted back into
■
CMXLHB5
the sheath on the head strap all the time when the unit is stored or not in use.
To reduce risk of damage to the built-in USB plug cable, pull by the plug rather than the cord when disconnecting.
■
Do not attempt to charge the unit if the built-in USB plug or cable is damaged – contact customer service.
■
WARNING –
FIRE HAZARD:
Keep head lamp away from materials that may burn.
■
Do not expose this unit to extremely high temperatures, sparks or flames.
■
CAUTION –
TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE:
Do not place or immerse the light in water or other liquid. Do not place or store the light where it can fall or be pulled into water or become wet. Detach the light from
■
the head strap before washing the head strap.
The LEDs get hot quickly. Do not touch the hot lens, guard or enclosure.
■
Never look directly into the light or shine the light into another person' s eyes.
■
Keep sharp objects away from lens – it can crack or break.
DETACHABLE, ADJUSTABLE
■
Do not drop or throw the head lamp. It contains a lithium-ion battery.
HEAD STRAP ■
Do not open the light body casing. There are no user-serviceable parts inside.
■
Do not operate the light without the lens in place.
■
When not in use, the appliance should be stored in a dry, well ventilated place out of the reach of children.
■
SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM-ION BATTERIES
WARNING –
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, BURST HAZARD, OR INJURY TO PERSONS OR PROPERTY:
Lithium-ion batteries are small, compact and ideal for providing long-lasting power to this unit. However, they must be used and charged properly. Improper use can
result in serious injury, fire, or death.
Lithium-ion batteries can explode in the presence of a source of ignition. Do not use the product in the presence of an open flame.
■
Do not place this lithium-ion battery powered unit in fire or apply heat to it.
■
Do not subject this lithium-ion battery powered unit to strong impacts or shocks. The battery in this unit contains safety and protection devices which, if damaged, may
■
cause the battery to generate heat, rupture or ignite.
Do not expose the lithium-ion battery to water or salt water, or allow the battery to get wet.
■
Avoid storing this lithium-ion battery powered unit in the basement, bathroom or other areas of the house that are or may become wet or where humidity and moisture
■
may concentrate.
Do not leave this lithium-ion battery powered unit in direct sunlight, or use or store the unit inside cars in hot weather. Doing so may cause the battery to generate heat,
■
SHEATH FOR USB PLUG
rupture, or ignite. Using the battery in this manner may also result in a loss of performance and a shortened life expectancy.
Never charge this unit near heat or flammable objects.
■
NEVER THROW WATER ON A BURNING LI-ION BATTERY!
BC
■
if it comes in contact with water or even moisture in the air. A fire extinguisher must be used.
Battery Charging and Capacity
This unit is delivered in a partially charged state – you must fully charge it before using it for the first time.
When stored at room temperature with a full charge, li-ion batteries will begin to discharge from the time they are manufactured, even when unused. Deep discharges also
decrease their capacity. Battery life can be extended by the following:
Charge battery to full capacity before storage.
■
Optimal storage temperature for this unit is between 5°C and 20°C (41°F and 68°F).
■
Never discharge the battery fully.
■
Charge after each use.
■
Always charge at least once every 3-6 months if not in frequent use to prevent overdischarge.
■
Transportation of lithium-ion batteries
Always check all applicable local, national, and international regulations before transporting a unit containing a lithium-ion battery.
■
Transporting an end-of-life, damaged, or recalled battery may, in certain cases, be specifically limited or prohibited.
■
INSTRUCTIONS PERTAINING TO THE WEATHER-RESISTANT HEADBAND LIGHT
The lens, Power/Light Mode Button and the bushing of USB charging cord act to preserve the weather-resistant qualities of the light and prevent water from entering the
gap. An undamaged lens, power button and the bushing of the USB charging cord before use are very important.
CAUTION –
TO REDUCE THE RISK OF PROPERTY DAMAGE:
Use of the unit with a damaged lens, Power/Light Mode Button or the bushing of USB charging cord, and/or submerging the light in water may cause the light to no
longer be weather-resistant. Do not use the light if these conditions exist or it could sustain permanent damage.
SAVE THESE INSTRUCTIONS
CHARGING/RECHARGING
This unit is shipped in a partially charged state. Fully charge the unit after purchase and before first use using built-in USB plug until the two Red LED Area Lights light.
Recharge after each use until the two Red LED Area Lights light.
IMPORTANT: When the unit is not in use, we recommend that the battery is charged at least every 3 to 6 months.
Procedure
1. Make sure the headlamp is turned off.
2. Remove the built-in USB plug from the sheath on the head strap.
3. Insert the built-in USB plug into a working USB power port. The two Red LED Area Lights will flash to indicate the unit is charging.
4. Charge until the two Red LED Area Lights light.
5. When charging is complete, disconnect the built-in USB plug from the USB power port. Make sure the built-in USB plug is properly inserted back into the sheath
on the head strap whenever the unit is stored or not in use.
IMPORTANT NOTES:
Once it begins charging, the headlamp will not operate until the built-in USB plug is disconnected.
If the built-in USB plug is plugged into a working USB power port while the headlamp is operating, the light will shut off and the unit will begin charging.
If the battery of the unit is overheated (due to extensive use or recharging) or is too cold (the ambient temperature has dropped below -20°C) during the charging process,
the two Red LED Area Lights will flash rapidly. The charging process will stop at this stage and will automatically resume after a cool down/warming period.
OPERATING INSTRUCTIONS
Attaching the Headlamp with the Head Strap
The unit is provided with the detachable head strap. Attach the head strap to the back of unit. Place the headlamp on your head and adjust the head strap to fit securely.
Operate the light as outlined in the following section.
IMPORTANT: The headlamp body is detachable from the head strap. However, manufacturer strongly recommends that you not detach it unless absolutely necessary.
Operating the Headlamp
The headlamp is controlled by the Power/Light Mode Button at the top center of the light. To operate the headlamp, disconnect the built-in USB plug from the device' s
USB Power Port, and then select the desired light mode by pressing the Power/Light Mode Button.
For High (Bright) Mode:
To turn the headlamp on and use the Main LED light bulb in high intensity, press the Power/Light Mode Button once.
■
For Low (Dimmer) Mode:
■
a second time within 2 seconds.
For Area Light Mode (two Red LED Area Lights):
■
within 2 seconds.
To Turn the Flashlight Off:
■
in any mode.
For Flash Mode:
■
Flash Mode, press the Power/Light Mode Button once.
IMPORTANT NOTES:
Zooming / Focusing the Headlamp
The light beam on the Main LED Bulb can either be focused (for use as a spotlight) or zoomed out (for use as an area light) by rotating the Zoom/Focus Knob around
the lens.
To zoom out the light beam, rotate the Zoom/Focus Knob forward (clockwise).
■
To focus the light beam, rotate the Zoom/Focus Knob backward (counter-clockwise).
■
CAUTION –
The Zoom/Focus Knob was designed to rotate forward and backward only. Do not attempt to "force" the Zoom/Focus Knob beyond its maximum angle.
■
Forcibly and repeatedly rotating the Zoom/Focus Knob forward and backward may damage the pivoting mechanism.
■
Pivoting the Headlamp Main Body
The headlamp body is adjustable, allowing the headlamp to be tilted forward and backward to adjust the area of illumination, as shown:
CAUTION –
The headlamp body was designed to tilt forward and backward only. Do not attempt to "force" the headlamp body beyond its maximum angle.
■
The headlamp body is not designed to be detached from the head strap. Do not attempt to detach it at any time.
■
Forcibly and repeatedly tilting the headlamp forward and backward may damage the pivoting mechanism.
■
CARE AND MAINTENANCE
If the unit gets dirty, gently clean the outer surfaces of the headlamp with a soft cloth. Never immerse the unit in water or any other liquid.
TROUBLESHOOTING
If a lithium-ion battery does catch on fire, it will burn even more violently
The headlamp does not charge
Check that the light is turned off.
■
Check that the built-in USB Plug is properly inserted into a device' s USB power port. Confirm that the USB port is working and make sure there is good contact.
■
Check that the built-in USB Plug is clean and the cable is not damaged.
■
The headlamp does not operate
Make sure the Power/Light Mode Button is pressed to turn the light on.
■
The headlamp will not operate when charging. Be sure the built-in USB Plug is disconnected before headlamp use.
■
The internal battery may be completely discharged. Charge the unit following the directions.
■
If the unit does not operate after recharging as directed, contact manufacturer at 888-331-4569.
■
ACCESSORIES
Recommended accessories for use with this unit may be available from the manufacturer. If you need assistance regarding accessories, please contact manufacturer at
888-331-4569.
WARNING:
SERVICE INFORMATION
Whether you need technical advice, repair, or genuine factory replacement parts, contact the manufacturer at 888-331-4569.
ONE-YEAR LIMITED WARRANTY
The manufacturer warrants this product against defects in materials and workmanship for a period of ONE (1) YEAR from the date of retail purchase by the original end-
user purchaser ("Warranty Period").
If there is a defect and a valid claim is received within the Warranty Period, the defective product can be replaced or repaired in the following ways: (1) Return the product
to the manufacturer for repair or replacement at manufacturer' s option. Proof of purchase may be required by manufacturer. (2) Return the product to the retailer where
product was purchased for an exchange (provided that the store is a participating retailer). Returns to retailer should be made within the time period of the retailer' s return
policy for exchanges only (usually 30 to 90 days after the sale). Proof of purchase may be required. Please check with the retailer for their specific return policy regarding
returns that are beyond the time set for exchanges.
This warranty does not apply to accessories, bulbs, fuses and batteries; defects resulting from normal wear and tear, accidents; damages sustained during shipping;
alterations; unauthorized use or repair; neglect, misuse, abuse; and failure to follow instructions for care and maintenance for the product.
This warranty gives you, the original retail purchaser, specific legal rights and you may have other rights which vary from state to state or province to province. This
product is not intended for commercial use.
Please complete the Product Registration Card and return within 30 days from purchase of the product to: Baccus Global LLC, 621 NW 53rd St., Suite 450, Boca Raton,
FL 33487. Baccus Global LLC, toll-free number: 888-331-4569.
SPECIFICATIONS
Input:
Bulb:
Battery:
Importados por Baccus Global LLC, 621 NW 53rd St., Suite 450, Boca Raton, FL 33487
www.Baccusglobal.com • 888-331-4569
To use the headlamp' s Main LED light bulb in low intensity, press the Power/Light Mode Button
To use the headlamp' s two Red LED Area Lights, press the Power/Light Mode Button a third time
Press the power/light mode button a fourth time within 2 seconds OR press the Power/Light Mode Button once after 2 seconds
To use all the LEDs flashing, press and hold the Power/Light Mode Button anytime for approximately 2 seconds. To turn the light off in
If the light' s internal battery level is too low, the built-in low voltage protection may activate after a short period of operation, then the light will automatically shut down. This
is a special feature to protect the internal lithium-ion battery from damage. Recharge the battery before continuing use.
The headlamp will not operate when charging. Be sure the built-in USB Plug is disconnected before headlamp use.
TO REDUCE THE RISK OF PROPERTY DAMAGE:
TO REDUCE THE RISK OF PROPERTY DAMAGE:
The use of any accessory not recommended for use with this appliance could be hazardous.
5V DC, 1A
One Main LED Bulb, two Red LED Area Lights
Lithium-Ion, 3.7V DC
RD063020
6/30/2020 1:04:55 PM 6/30/2020 1:04:55 PM