Tabla de contenido
Publicidad
SET POINT DISPLAY
Select timer to be displayed as show
in timer display selection
SEL
OP1
OP2
PRG
OP3
OP4
OP5
UMT
SEL
OP1
OP2
PRG
OP3
OP4
OP5
UMT
SEL
OP1
OP2
PRG
OP3
OP4
OP5
UMT
SEL
OP1
OP2
PRG
OP3
OP4
OP5
UMT
The display will then revert to showing the
actual value of the currently selected timer
FOR CYCLE TIMER
DELAY OFF
(dodo)
SEL
OP1
OP2
PRG
OP3
OP4
OP5
UMT
SEL
OP1
OP2
OP3
PRG
OP4
OP5
UMT
SEL
OP1
OP2
PRG
OP3
OP4
OP5
UMT
SEL
OP1
OP2
PRG
OP3
OP4
OP5
UMT
The display will then revert to showing the
actual value of the currently selected timer
TIMING MODES
dE (CtS)
Supply
Input
OP
T
T
dd
Supply
Input
OP
T
SET POINT ADJUSTMENT
Press SEL
Display indicates timer 1
set point 1 will be displayed
if no more keys are pressed
Press /\ to change to the set
point of the next timer.
Display indicates timer 2
set point 1 will be displayed
if no more keys are pressed
Press /\ to change to the set
point of the next timer.
If no further keys are
pressed, the set point of the
currently selected timer will
be shown for 2-3 seconds.
(timer 2, time 1 in this case)
(cct)
AND DELAY ON -
MODES ONLY
Press SEL
FOR CYCLE TIMER
Display indicates timer 1
set point 1 will be displayed
if no more keys are pressed
Press SEL to change to the
second set point of this timer.
Display indicates timer 1
set point 2 will be displayed
if no more keys are pressed
Press /\ to change to the set
point of thenext timer.
If no further keys are
pressed, the set point of the
currently selected timer will
be shown for 2-3 seconds.
(timer 1, time 2 in this case)
dE (PtS)
dE (Ptr)
T
T
T
T1
T2
T1
T
SEL
OP1
OP2
Press PRG
PRG
OP3
OP4
OP5
UMT
Display indicates access
SEL
OP1
to timer 1, set point 1.
OP2
PRG
OP3
OP4
Press /\ to change to the set
OP5
point of the next timer.
UMT
SEL
Display indicates access
OP1
OP2
OP3
PRG
OP4
to timer 2, set point 1.
OP5
Press SEL to change the
UMT
first digit of the set time.
Use /\ or V keys to set the
SEL
OP1
first digit to the required
OP2
PRG
OP3
OP4
time. Press SEL to move to
OP5
the next digit and repeat for
UMT
each digit.
SEL
OP1
OP2
When the desired time has
PRG
OP3
OP4
OP5
been set, press PRG.
UMT
The digit will stop flashing and
SEL
OP1
the display will revert to showing
OP2
PRG
OP3
OP4
the actual value of the currently
OP5
selected timer (single timer
UMT
modes only).
(cct)
AND DELAY ON -
DELAY OFF
(dodo)
MODES ONLY
SEL
Display indicates access
OP1
OP2
PRG
OP3
OP4
to timer 2, set point 2.
OP5
Press SEL to change the
UMT
first digit of the set time.
Use /\ or V keys to set the
SEL
OP1
first digit to the required
OP2
PRG
OP3
OP4
time. Press SEL to move to
OP5
the next digit and repeat for
UMT
each digit.
SEL
OP1
OP2
When the desired time has
PRG
OP3
OP4
OP5
been set, press PRG.
UMT
SEL
The digit will stop flashing
OP1
OP2
PRG
and the display will revert to
OP3
OP4
OP5
showing the actual value of
UMT
the currently selected timer.
Int (CtS)
Int (PtS)
T
T
T
cct
T1
T2
T1
T1
T2
Int (Ptr)
T
T
T
dodo
T2
T1
T2
Publicidad
Tabla de contenido
