BLACK&DECKER RC600 Manual De Instrucciones

R R C C 6 6 0 0 0 0 - -
R R C C 6 6 0 0 0 0 - -
Intended use
The RC600 replacement chain has been specifically designed for
TM
the Alligator Lopper .
WARNING: Read all instructions. Failure to follow all
instructions listed below may result in electric shock, fire and/or
serious injury.
SAVE THESE INSTRUCTIONS
Reduced Kickback Chain - The RC600 chain is designed with a
contoured depth gauge and guard link which deflect kickback force
and allow wood to gradually ride into the cutter.
WARNING: Some dust created by power sanding, sawing,
grinding, drilling, and other construction activities contains
chemicals known to cause cancer, birth defects or other
reproductive harm. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry
products, and
• arsenic and chromium from chemically-treated lumber. (CCA)
Your risk from these exposures varies, depending on how often
you do this type of work. To reduce your exposure to these
chemicals: work in a well ventilated area, and work with
approved safety equipment, such as those dust masks that are
specially designed to filter out microscopic particles.
• Avoid prolonged contact with dust from power sanding,
sawing, grinding, drilling, and other construction activities.
Wear protective clothing and wash exposed areas with soap
and water. Allowing dust to get into your mouth, eyes, or lay on
the skin may promote absorption of harmful chemicals.
WARNING: Use of this tool can generate and/or disburse
dust, which may cause serious and permanent respiratory or
other injury. Always use NIOSH/OSHA approved respiratory pro-
tection appropriate for the dust exposure. Direct particles away
from face and body.
WARNING: Always wear eye protection.
CAUTION: Wear appropriate personal hearing protection during
use. Under some conditions and duration of use, noise from this
product may contribute to hearing loss.
Removing the saw chain & chain bar (figs. A & B)
WARNING: Before chain or other adjustments, make sure
that the tool is switched off and unplugged.
WARNING: Laceration hazard. Always wear protective gloves
when installing or removing the saw chain. The saw chain is sharp
and can cut you when it is not running.
WARNING: Burn hazard. The chain guide bar and chain may
become hot during use. Allow to cool before adjustment or
removal.
- Place the tool on a firm surface.
- Rotate the two retention nuts (1) counter clockwise with wrench
(2) provided and remove completely.
- Remove the chain access cover (3).
- Open the handles and pull back the top chain cover (4).
- Pull back chain bar (5) and then lift the saw chain (6) out of the
groove in the guide bar. The chain can then be removed from the
unit.
- The chain bar can then be angled up and over the bolts
.
Assembling the chain bar and chain (figs. C&D)
WARNING: Before chain or other adjustments, make sure
that the tool is switched off and unplugged.
WARNING: Always wear protective gloves when installing or
removing the saw chain. The saw chain is sharp and can cut you
when it is not running.
- Ensure the operation is carried out on a firm surface.
- Open the handles and pull back the top chain cover (4).
- Insert the chain bar (5) into the space between the chain
tensioner and the first bolt, angle the chain bar down over the
bolts.
- Place the chain (6) around the front of the chain bar and
engage in the nose sprocket of the chain bar. Make sure chain is
installed properly, with the cutting teeth facing forward as shown
here.
Pull the chain bar and chain back, engaging it in the groove in the
chain bar and then over the sprocket (7) positioning teeth in the
correct position on the sprocket.
- Replace the chain access cover (3)(fig.A) and retention nuts (1)
(fig.A) tightening securely.
R R e e p p l l a a c c e e m m e e n n
R R e e p p l l a a c c e e m m e e n n
RC600 - INSTRUCTION SHEET
t t c c h h a a i i n n f f o o r r
t t c c h h a a i i n n f f o o r r
Service Information
Whether you need technical advice, repair, or genuine factory
replacement parts, contact the Black & Decker location nearest
you. To find your local service location, refer to the yellow page
directory under "Tools–Electric" or call:
1-800-54-HOW TO (544-6986).
Black & Decker (U.S.) Inc.,
701 E. Joppa Rd.
Towson, MD 21286 U.S.A.
Cat No. RC600
Copyright © 2006 Black & Decker
A A A A
A
LLIGATOR LLIGATOR LLIGATOR
LLIGATOR LLIGATOR
A
B
4
5
C
4
D
6
7 7
Form #493205-00
Printed in China
L L P P 1 1 0 0 0 0 0 0
L L P P 1 1 0 0 0 0 0 0
TM
6
5
6
See 'Tools-Electric'
– Yellow Pages –
for Service & Sales
FEB.-06