Westin 22-1535 Instrucciones

AUTOMOTIVE PRODUCTS, INC.
MOUNT KIT
EQUIPO DE MONTAJE
TROUSSE DE MONTAGE
22-1535
22-0040, 22-5040
22-0045, 22-5045
22-6040, 22-6045
22-6020, 22-6025
ITEM QTY
1,2 2 STEP BAR, PASSENGER (1) AND DRIVER (2) (SOLD SEPARATELY)
3 6 MOUNT BRACKET
4 12 M8-1.25 X 20MM HEX HEAD BOLT
5 18 5/16" FLAT WASHER
6 12 5/16" LOCK WASHER
7 10 M8-1.25 HEX NUT
8 6 M6 BOLT PLATES (INCLUDED WITH STEP TUBES )
9 24 M6 FLAT WASHERS (INCLUDED WITH STEP TUBES)
10 24 M6 LOCK NUTS (INCLUDED WITH STEP TUBES)
1,2 2 ESTRIBOS, ACOMPAÑANTE (1) CONDUCTOR (2) (SE COMPRA
SEPARADO
3 6 SOPORTES DE MONTAJE
4 12 PERNOS CON CABEZA HEXAGONAL M8-1,25 X 20 MM
5 18 ARANDELAS PLANAS DE 5/16"
6 12 ARANDELAS DE PRESIÓN DE 5/16"
7 10 TUERCAS HEXAGONALES DE M8-1,25
8 6 TORNILLO M6 PLACAS (INCLUIDO CON TUBOS STEP)
9 24 M6 ARANDELAS PLANAS (INCLUIDO CON TUBOS DE PASO)
10 24 Las TUERCAS M6 (INCLUIDO CON TUBOS DE PASO)
1,2 2 MARCHE-PIEDS, PASSAGER (1) ET CONDUCTEUR (2) (ACHETE
SEPAREMENT)
3 6 SUPPORTS DE MONTAGE
4 12 BOULONS A TETE HEXAGONALE M8-1,25 X 20MM PO
5 18 RONDELLE PLATE 5/16 PO
6 12 RONDELLES A FREIN 5/16 PO
7 10 ÉCROUS HEXAGONAUX M8-1,25
8 6 Boulon M6 PLAQUES (inclus avec TUBES STEP)
9 24 M6 RONDELLES PLATES (inclus avec TUBES STEP)
10 24 NUTS M6 LOCK (inclus avec TUBES STEP)
STEP 1. Remove contents from box and check for damage. Verify all parts are present. Read instructions completely before
beginning.
STEP 2. Install brackets as shown. Hand tighten. SEE FIGURE 1.
STEP 3. To install oval step tubes, use mounting hardware packaged with step tubes. Insert M6 bolt plates into the oval tube
as shown . Place bolts through the corresponding mount holes into the brackets. Attach with M6 flat washers and
M6 lock nuts. SEE FIGURE 2,3,4 ( For 6" tubes see sheet included with tubes for further installation instructions.)
STEP 4. Make sure step bar and brackets are properly aligned and tighten fasteners. Recommended torque values are 22 Ft.
Lbs. for M8 fasteners and 7 Ft. Lbs. for M6 fasteners.
STEP 5. Repeat installation for opposite side.
FINISH PROTECTION
Westin products have a high quality finish that must be cared for like any other exposed finish on the vehicle. Protect the finish with a non-abrasive automotive wax,
(e.g. Pure Carnauba) on a regular basis. The use of any soap, polish or wax that contains an abrasive is detrimental, as the compounds scratch the finish and open it
1
INSTRUCTIONS-INSTRUCCIONES-CONSIGNES
APPLICATION: 2002-10 CHEVY AVALANCHE
APLICACIÓN:
APPLICATION: CHEVY AVALANCHE 2002-10
CONTENTS - CONTENIDO
)
2005-10 CHEVY SUBURBAN/TAHOE/GMC YUKON, YUKON XL
CHEVY AVALANCHE MOD. 2002-10 ,
CHEVY SUBURBAN/TAHOE/GMC YUKON, YUKON XL, MOD. 2005-10
CHEVY SUBURBAN/TAHOE/GMC TYUKON, YUKON XL 2005-10
2
- CONTENU
:
1
TOOLS - HERRAMIENTA
7/16" SOCKET
13MM SOCKET
13MM WRENCH
10MM SOCKET
10MM WRENCH
RATCHET
TORQUE WRENCH
DADO DE 7/16"
DADO DE 13MM
LLAVE DE TUERCAS DE 13MM
DADO DE 10MM
LLAVE DE TUERCAS DE 10MM
MANERAL
LLAVE DE TORQUE
DOUILLE 7/16 PO
DOUILLE 13MM
CLÉ 13MM
DOUILLE 10MM
CLE 10MM
CLIQUET
ClÉ DE COUPLE
75-0606 REVISION E 2/8/11
3
- OUTILS