Publicidad
Enlaces rápidos
FORD RANGER PX/MAZDA BT50 GEN 2 - RTS554
Important:
1. Check the Rhino-Rack website to ensure you have the latest issue of these instructions.
2. Please refer to your fitting instruction to ensure that the roof racks are installed in the correct locations.
3. Check the contents of kit before commencing fitment and report any discrepancies.
4. Place these instructions in the vehicle's glove box after installation is complete.
5. These instructions must be followed for warranty to be upheld.
Fit Time: 120min
Rhino-Rack, 22A Hanson Pl, Eastern
Creek NSW 2766, Australia
(02) 8846 1900
rhinorack.com.au
rhinorack.com
CONTROLLED
FORD RANGER SHOWN
ALSO COMPATIBLE WITH
MAZDA BT50 GEN2
Document No: R2424
Issue No: 02
Issue Date: 09/10/2020
Page 1 of 6
Page 1 of 5
Publicidad
Manuales relacionados para Rhino-Rack RTS554
Resumen de contenidos para Rhino-Rack RTS554
- Página 1 FORD RANGER PX/MAZDA BT50 GEN 2 - RTS554 Important: 1. Check the Rhino-Rack website to ensure you have the latest issue of these instructions. 2. Please refer to your fitting instruction to ensure that the roof racks are installed in the correct locations.
- Página 2 It is your responsibility to ensure these fitting instructions are given to the end user or client. These instructions remain the property of Rhino-Rack Australia Pty. Ltd. and may not be used or changed for any other purpose than intended.
-
Página 3: Capacidad De Carga
RTS554 Instructions Capacidad de Carga Revise el manual del propietario de su vehículo para la capacidad máxima de carga. Por favor asegúrese de solo usar la cantidad máxima de carga para el techo permitida por el manufacturero, si es menor que lo enlistado en la siguiente tabla. La carga debe de ser distribuida equivalentemente sobre el Sistema. - Página 4 RTS554 Instructions Parts list Lista de partes LEFT RIGHT x Pair FRONT NOTE: THE TRACKS ARE LEFT & RIGHT HANDED THE SINGLE LARGE RECTANGULAR CUT OUT DENOTES THE REAR LEFT Track RIGHT Track OUTSIDE OUTSIDE -Tools Required: Item Description -Herramientas necesarias:...
- Página 5 RTS554 Instructions 200mm AUS/NZ Ranger only -Tooling mark in ditch fill. -Marca de herramienta USA Ranger only. Ditch mould tooling line. 1 9/16” (40mm) 7 1/4” (185mm) from REAR Page 5 of 12...
- Página 6 RTS554 Instructions 165mm AUS/NZ Ranger A. Knife cut the rear section of A. Slice the trim exactly on the line in the the trim exactly on the line in the moulding location marked in steps 2a & 3. moulding location. The line is approximately 185mm from the back edge of the moulding.
- Página 7 RTS554 Instructions USA Ranger only. A. Carefully cut the trim exactly on the lines marked in steps 2b & 3. B. Make sure you apply protection on both sides of the track to prevent the knife from slipping & marking the roof.
- Página 8 RTS554 Instructions Top view: 1/8” (3mm) 90° Top view: 3/16” (5mm) 90° Page 8 of 12...
- Página 9 RTS554 Instructions -Drying time -Tiempo de secado 15min -IMPORTANT -IMPORTANTE Page 9 of 12...
- Página 10 RTS554 Instructions Page 10 of 12...
- Página 11 RTS554 Instructions Ensure rivets are seated correctly DO NOT STRIKE THE RIVET STEM WITH ANY - Si los remaches no están asentados TOOLS AS IT MAY PREVENT IT FASTENING correctamente CORRECTLY Page 11 of 12...
- Página 12 RTS554 Instructions NOTE: If fitting a backbone refer to the latest issue of the backbone instruction on the website & use the following backbone measurement Position the front edge of the foot 240mm from the top of the windscreen Top of windscreen...