Resumen de contenidos para Dorel Home Products Twin
Página 1
Visit www.dhpfurniture.com/eng/support-home or call Toll-Free 1-800-267-1739 Date of Purchase Lot Number THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE. B344045439W02 - 10125-M R.X. - 2017/8/17 2014 Dorel Home Products All Rights Reserved...
Warranty Information Read Before Beginning Assembly DHP warrants this product to be free from defects in material and workmanship and Call our toll free number if you need assistance. agrees to remedy any such defect. This warranty covers one year from the date of Work in a spacious area and near where the unit will be used, preferably on a original purchase.
Página 4
Parts For Daybed Replacement Parts, Visit www.dhpfurniture.com/eng/support-home This item is packed in 2 boxes! All parts listed on this page are in Box A. If Box B is missing please contact your Retailer. There are inner box(es) that include components required to complete this assembly.
Página 5
Parts For Daybed Replacement Parts, Visit www.dhpfurniture.com/eng/support-home This item is packed in 2 boxes! All parts listed on this page are in Box B. If Box A is missing please contact your Retailer. There are inner box(es) that include components required to complete this assembly.
Página 6
Parts For Trundle Replacement Parts, Visit www.dhpfurniture.com/eng/support-home This item is packed in 2 boxes! All parts listed on this page are in Box B. If Box A is missing please contact your Retailer. There are inner box(es) that include components required to complete this assembly.
Página 7
Hardware Pack: Daybed Hardware Pack #: T4019257A-00 1/4" X 3/4" 1/4"X 1 3/16" X 34 1/4"X 1 9/16" X 14 Please do not completely tighten all the hardware, until the entire assembly is complete, unless otherwise indicated in the step-by-step instructions.
Página 8
Hardware Pack: Trundle Hardware Pack #: T4144719LS-01 1/4" 1/4"X 3/4" 1/4"X 1 3/8" 1/4"X 1 9/16" Wrench Please do not completely tighten all the hardware, until the entire assembly is complete, unless otherwise indicated in the step-by-step instructions. The screw(s), bolt(s) to be used at each step are shown in actual size in the lower right corner of the page.
Página 9
Step 1 The following instructions will illustrate how Remove the protective to assemble the Daybed from Step 1 to plastic cap on the tip of Step 8. Please use the Daybed Hardware thread before assembling. Pack: T4019257A-00. Attach Z x 4 to C and D; Screw to C and D as illustrated, don't completely tighten.
Página 10
Step 2 Attach S x 2 and T x 2 to A with Attach S and T to B with Small holes on slots of S and T should be facing upward. X 12...
Página 11
Step 3 Attach E to A with Slat Cap holes on part E should be facing upward.
Página 12
Step 4 Attach E to B with Slat Cap holes on part E should be facing upward.
Página 13
Step 5 Hang A & B on C & D as illustrated below, don't completely tighten untill STEP 7 is complete.
Página 14
Step 6 Slat Cap holes on part F should Attach F to C, D with be facing upward.
Página 15
Step 7 Attach K to C, D with , then properly tighten all the BOLTS.
Página 16
Step 8 8.1 Insert O into X ; 8.2 Press X into E , repeat the same procedure for the opposite side. 8.3 Insert ends of both slats O into Y , then press Y into F as illustrated. Repeat the same procedures going backwards for every row of slats.
Página 17
Step 9 Caster holes on H The following instructions will illustrate how towards upward. to assemble the Trundle from Step 9 to Step 13. Please use the Trundle Hardware Pack: T4144719LS-01. Slat holes on part (I/J) 9.1 Lay H x 2 on the floor with holes towards towards floor as illustreated.
Página 18
Step 10 Attach I x 2 & J to H x 2 with using using...
Página 19
Step 11 Attach P x 2 & N x 2 to H x 2 with In order not to damage your product, please orient the lever of the caster to the inside of the trundle as illustrated To facilitate the use of the trundle, please assemble the caster N close to part J as illustrated...
Página 20
Step 12 Turn over the frame assembled from STEP 11. Attach G to J with Note: Check if all the slat cap holes on I, J are orientated on the top side...
Página 21
Step 13 13.1 Insert O into X; 13.2 Press X into J, repeat the same procedure for the opposite side to Press X into I. 13.3 Insert ends of both slats O into Y, then press Y into I as illustrated. Repeat the same procedures going backwards for every row of slats.
Helpful Hints To use Trundle: How to lock caster? Pull out the trundle completely from How to unlock caster? underneath daybed. Once positioned, make sure casters are locked by pushing down the lever " " as illustrated "How to lock caster?". To store Trundle: Unlock the casters by pushing down the lever "...
Página 23
Prohibit jumping and horseplay on this bed. Only use mattress which is 74" - 75" long and 37 1/2" - 38 1/2" wide. To optimize use of trundle, use a standard twin size mattress, no thicker than 8 . Do not use risers under this bed.
Página 24
Si le faltan piezas o las que se incluyen est n da adas, con Linen Daybed with Trundle mucho gusto le enviaremos sus piezas de reemplazo sin cargo extra. Twin Visite www.dhpfurniture.com/spa/support-home Gris o llame gratis al 1-800-267-1739 Fecha de compra...
Lea antes de comenzar a ensamblar Partes Llame a nuestro numero gratuito si necesita asistencia. Piezas de reemplazo, visite www.dhpfurniture.com/spa/support-home Trabaje en un rea espaciosa y cerca de donde su producto ser utilizado, preferiblemente sobre una alfombra o utilice el cart n del empaque para proteger su piso y su producto.
Instrucciones Paso 1 Paso 13 Las instrucciones siguientes ilustrar n c mo ensamblar el Div n del Paso 1 al Paso 13.1 Inserte O dentro de X; 8. Utilice el paquete Daybed Hardware:T4019257A-00. 13.2 Presione X sobre E, repetir el mismo procedimiento para el lado opuesto. Una Z x 4 con C &...