Descargar Imprimir esta página

Mottura 3Dkey Manual De Instrucciones página 3

Publicidad

SOSTITUZIONE NUCLEO VERSIONE CHIAVE-POMOLO
Rimuovere la serratura dai fissaggi della porta e ruotarla sul lato esterno. Svitare le viti C per la rimozione della piastra in manga-
nese (fig. 1), togliere le viti D presenti sul nucleo (fig. 2), inserire la chiave ed estrarre il nucleo (fig. 3), sfilare la chiave recuperan-
do la piastra E di tenuta nucleo (fig. 4), riposizionare la piastra sul nuovo nucleo, smontare il pomolo interno, posizionare l'ingra-
naggio del nucleo come in figura 5, rimontare il nucleo e la piastra fissandoli con le viti D, posizionare la piastra in manganese
riavvitando le viti C, rimontare la serratura sulla porta, riposizionare il pomolo (fig. 6), ruotare fino ad innesto e avvitare le viti.
NUCLEO REPLACEMENT KEY-KNOB VERSION
Remove the lock from the door fixings and turn it to the outside. Unscrew the screws C to remove the manganese plate (Fig.
1). Remove the screw D (Fig. 2). Insert the key and remove the nucleo (Fig. 3). Remove the key by pulling off the nucleo se-
curing plate E (Fig. 4). Reposition the plate on the new nucleo, remove the internal knob, position the nucleo gear as shown
in figure 5. Reassemble the nucleo and the plate fixing them with the screws D, position the manganese plate by tightening
the screws C. Reassemble the lock on the door, reposition the knob (Fig. 6) and rotate until it engages. Tighten the screws.
SUSTITUCIÓN DEL NÚCLEO VERSIÓN LLAVE-POMO
Quitar la cerradura de las fijaciones de la puerta y girarla hacia el lado exterior. Desenroscar los tornillos C para quitar la
placa de manganeso (fig. 1), quitar los tornillos D presentes en el núcleo (fig. 2), introducir la llave y extraer el núcleo (fig.
3), sacar la llave recuperando la placa E de estanquidad del núcleo (fig. 4), volver a colocar la placa en el nuevo núcleo,
desmontar el pomo interior, colocar el engranaje del núcleo como en la figura 5, volver a montar el núcleo y la placa
fijándolos con los tornillos D, colocar la placa de manganeso y reapretar los tornillos C, volver a montar la cerradura en
la puerta, colocar nuevamente el pomo (fig. 6), girar hasta que se acople y enroscar los tornillos.
REMPLACEMENT NUCLEO VERSION CLÉ-BOUTON
Enlever la serrure des fixations de la porte et la faire tourner sur le côté extérieur. Dévisser les vis C pour démonter la plaque en man-
ganèse (fig. 1), enlever les vis D présentes sur le nucleo (fig. 2), introduire la clé et extraire le nucleo (fig. 3), faire sortir la clé en récupérant
la plaque E de fixation du nucleo (fig. 4), repositionner la plaque sur le nouveau nucleo, démonter le bouton intérieur, placer l'engrenage
du nucleo comme le montre la figure 5, remonter le nucleo et la plaque en les fixant avec les vis D, positionner la plaque en manganèse
en revissant les vis C, remonter la serrure sur la porte, repositionner le bouton (fig. 6), tourner jusqu'à son enclenchement et visser les vis.
ЗАМЕНА НУКЛЕО ВАРИАНТ КЛЮЧ-РУЧКА
Освободить замок от креплений к двери и снять его. Отвинтить винты C для демонтажа пластины из марганцевой
стали (рис. 1), вынуть находяшиеся на нуклео винты D (рис. 2), вставить ключ и извлечь нуклео (рис. 3), вынуть
ключ, отсоединяя стопорную пластину E для нуклео (рис. 4), установить пластину на новый нуклео, удалить
внутреннюю ручку, установить шестерню в положение, показанное на рисунке 5, установить заново нуклео и
пластину с помощью винтов D, установить пластину из марганцевой стали, затянув винты С, повторно закрепить
замок на двери, установить ручку (рис. 6), повернуть до щелчка, затянуть винты.
C
C
E
C
1
4
D
D
2
5
3
6

Publicidad

loading

Este manual también es adecuado para:

3d100 serie3d103 serie