Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

IB501001EN
Installation Instructions – Arbor Bollard
Instructions d'installation – Arbor Bollard
Instrucciones de instalación – Arbor Bollard
Risk of Fire, Electrical Shock, Cuts or other Casualty Hazards- Installation and maintenance of this
product must be performed by a qualified electrician. This product must be installed in accordance
with the applicable installation code by a person familiar with the construction and operation of the
product and hazards involved.
Risk of Fire and Electric Shock- Make certain power is OFF before starting installation or attempting
any maintenance. Disconnect power at fuse or circuit breaker.
Risk of Fire- Refer to product label for specific minimum supply conductor requirements.
Risk of Burn- Disconnect power and allow fixture to cool before handling or servicing.
Risk of Personal Injury- Fixture may become damaged and/or unstable if not installed properly.
Failure to comply with these instructions may result in death, serious bodily injury and property damage.
DISCLAIMER OF LIABILITY: Cooper Lighting Solutions assumes no liability for damages or losses of any kind
that may arise from the improper, careless, or negligent installation, handling or use of this product.
NOTICE: Green ground wire provided in proper location. Do not relocate.
ATTENTION Receiving Department: Note actual fixture description of any shortage or noticeable damage on
delivery receipt. File claim for common carrier (LTL) directly with carrier. Claims for concealed damage must be
filed within 15 days of delivery. All damaged material, complete with original packing must be retained.
Safety: This fixture must be wired in accordance with the National Electrical Code and applicable local codes and
ordinances. Proper grounding is required to insure personal safety. Carefully observe grounding procedure under
installation section.
APPLICATIONS: This lighting fixture is designed for outdoor lighting services, and should not be used in area
of limited ventilation or inside high ambient temperature enclosures. It must be stored in a dry location prior to
installation. Do not expose lighting fixture to rain, dust or other environmental conditions prior to installation
and insertion of photo control or shorting cap (if so equipped). Best results will be obtained if installed and
maintained according to the following recommendations.
WARNING
Brand Logo
reversed out of
black
INS #
INS #

Publicidad

Tabla de contenido
loading

Resumen de contenidos para Cooper Lighting Solutions Arbor Bollard

  • Página 1 Failure to comply with these instructions may result in death, serious bodily injury and property damage. DISCLAIMER OF LIABILITY: Cooper Lighting Solutions assumes no liability for damages or losses of any kind that may arise from the improper, careless, or negligent installation, handling or use of this product.
  • Página 2 Installation Instructions - Arbor Bollard INSTALLATION Anchor Bolts (3X) Tools Required 3/4”Conduit (2X) Lot Conduit Ratchet, a shallow 3/4” socket or 3/4” wrench for 1/2” Expose Atleast Project 1.00” hex nuts, #2 Phillips head screw driver, torque wrench and 10” of Wire (2X) Max (2X) 5/32”...
  • Página 3 Installation Instructions - Arbor Bollard 10. After base driver assembly is in position, add (1) 13. Lift fixture and slide it over base driver assembly and washer, (1) lock washer, and (1) nut per anchor bolt and align bottom holes with base extrusion. (Figure 4.) torque bolts to 30 ft.-lbs.
  • Página 4: Outillage Nécessaire

    La désobéissance aux instructions suivantes représente un risque de blessures graves ou mortelles et de dommages matériels. EXONÉRATION DE RESPONSABILITÉ : Cooper Lighting Solutions n’assume aucune responsabilité pour les dommages ou pertes de quelque nature que ce soit pouvant découler d’une installation, d’une manipulation ou d’une utilisation inappropriée, imprudente ou négligente de ce produit.
  • Página 5 Instructions d’installation - Arbor Bollard Enlevez l'ensemble pilote de base en desserrant trois Une fois que l'ensemble pilote est de niveau, insérez le vis du bas du luminaire et tirez l'ensemble pilote hors coussinet de base en caoutchouc et l'ensemble pilote.
  • Página 6 Instructions d’installation - Arbor Bollard 13. Soulevez le luminaire et faites-le glisser par-dessus l’ensemble pilote de base, puis alignez les orifices inférieurs avec l’extrusion de la base. (Figure 4.) emarque: Assurez-vous que les fils de mise à la terre et de DEL ne se retrouvent pas coincés entre l’ensemble pilote de base et...
  • Página 7: Renuncia De Responsabilidad

    El incumplimiento de estas instrucciones puede provocar la muerte, lesiones corporales graves y daños materiales. RENUNCIA DE RESPONSABILIDAD: Cooper Lighting Solutions no asume ninguna responsabilidad por daños o pérdidas de ningún tipo que puedan derivarse de la instalación, manipulación o uso incorrecto, descuidado o negligente de este producto.
  • Página 8 Instrucciones de instalación - Arbor Bollard Retire la unidad del controlador de base aflojando los Una vez que esté nivelada, introduzca la almohadilla de tres tornillos de la base de la luminaria y tire la unidad goma de la base y la unidad del controlador. Haga rotar del controlador para quitarla del alojamiento.
  • Página 9 Instrucciones de instalación - Arbor Bollard 13. Levante la luminaria y deslícela sobre la unidad del controlador de base y alinee los orificios inferiores con la extrusión de la base. (Figura 4.) ota: Asegúrese de que los cables del LED y a tierra no queden apretados entre la unidad del controlador de la base y el alojamiento.
  • Página 10: Garantías Y Limitación De Responsabilidad

    Garanties et limitation de responsabilité Veuillez consulter le site www.cooperlighting.com pour obtenir les conditions générales. Garantías y Limitación de Responsabilidad Visite www.cooperlighting.com para conocer nuestros términos y condiciones. Cooper Lighting Solutions is a registered trademark. All trademarks are property Cooper Lighting Solutions of their respective owners.

Tabla de contenido