Publicidad
Idiomas disponibles
Idiomas disponibles
Connections
Use shielded cable for the connections. One
end of the cable must be connected to Ground
on the Panel, and the other left free.
Examples A and B in the wiring diagram in Fig. 2
utilize terminal +N to activate Wave/WB or Wave/
WSB.
When using terminal +N to activate the device,
jumper J3 must be disconnected and terminal -
A must be connected to Ground (terminal
Examples A and B in the wiring diagram in Fig. 3
utilize terminal –A to activate Wave/WB or Wave/
WSB.
When using terminal –A to activate the device,
jumper J3 must be connected.
When connecting either Wave/W or Wave/WS re-
fer to Examples A and B in the wiring diagram in
Fig. 4.
Examples A and B in the Wiring diagrams show
the connection of Wave Series devices to two
different types of Panel terminal boards.
The acronyms that identify the terminals in the wir-
ing diagrams (Figures 2, 3 and 4) are valid for Cus-
tom Panels only, therefore, when connecting the
device to Non-Custom Panels consider that:
¾ terminal +B supplies a 13.8 V Direct Current;
¾ terminal +N supplies the Positive Voltage
(13.8 V) during Panel Standby status,
whereas it is open (floating) during Alarm sta-
tus;
7(50,1$/ '(6&5,37,21
7DPSHU WHUPLQDOV $6 ZLOO .ORVH ZKHQ WKH 7DPSHU
$6
6ZLW.K .ORVHV DQG ZLOO RSHQ ZKHQ WKH 7DPSHU
6ZLW.K RSHQV
3RZHU :DYH:% DQG :6%
9
P$ 0D[
&RQWURO ,QSXW :DYH: DQG :6
%
7KH GHYL.H Z LOO KROG 6W DQGE\ VW DW XV Z KLOH
7HUPLQDO % LV RSHQ IORDWLQJ 7KH GHYL.H ZLOO
D.WLYDW H Z KHQ WHUPLQDO % .RQQH.W V WR W KH
3RVLWLYH 9ROWDJH 9
&RQWURO ,QSXWV :DYH:% DQG :6%
7KH GHYL.H ZLOO KROG VWDQGE\ VWDWXV ZKLOH WHUPLQDO
1
1 LV .RQQH.WHG WR WKH 3RVLWLYH 9ROWDJH 9
±$
DQG WHUPLQDO ±$ LV .RQQH.WHG WR *URXQG WKH
GHYL.H ZLOO D.WLYDWH ZKHQ HLWKHU WHUPLQDO 1 RU ±$
RSHQV IORDWLQJ
*URXQG
¾ terminal NC is closed to terminal COM during
Panel Standby status, whereas it is open
(floating) during Alarm status;
¾ terminal NO is open (floating) during Panel
Standby status, whereas it is closed to Ter-
minal COM during Alarm status;
¾ terminal OC is closed to Ground (terminal -
during Panel Standby status, whereas it is
open (floating) during Alarm status;
¾ terminal +A supplies the Positive Voltage
(13.8 V) during Panel Alarm status, whereas
).
it is open (floating) during Standby status.
If Tamper detection is required: connect terminals
AS in series to the Panel tamper line.
7(&+1,&$/ 63(&,),&$7,216
2SHUDWLQJ 9ROWDJH
&XUUHQW GUDZ
%
:DYH:% DQG :DYH:6%
:DYH:
:DYH:6
%DWWHU\ DUW &%
6RXQG RXWSXW
&DQGHOD
3URWH.WLRQ 5DWLQJ
2SHUDWLQJ 7HPSHUDWXUH 5DQJH
'LPHQVLRQV / [ + [ 3
:HLJKW
- -
- - )
9
P$ 0D[
P$
P$
$$ P$K 9
“ G% DW P
.G
,3
ƒ& WR ƒ&
[ [ PP
J 0D[
Publicidad
