Charger Operation - Flexzilla L1388LFZ Instructivo Del Propietario

READ AND FOLLOW ALL INSTRUCTIONS BEFORE USE.
SAVE THESE INSTRUCTIONS FOR FUTURE USE.
AUTOMATIC BLEEDER VALVE: (see figure 1):
• Bleeds air when reconnectitng the barrel and head.
• Reduces air locks & priming problems.
SHOULDER STRAP (see figure 2):
Attach strap by latching each end into the hole located on the head casting and hanger at the back of the
handle.
HOSE DOCK (see figure 3):
Insert the grease coupler end of the grease hose into the loop hole located on the side of the housing
when gun is not in use.
PRESSURE RELIEF VALVE (see figure 4):
CAUTION: Never allow any part of the human body to come in front of, or in direct contact with a grease
discharge outlet. Direct the air pocket valve away from yourself and other persons in the vicinity. Never
point the nozzle of the gun at yourself or toward anyone else. Pressure relief is factory preset at 7000 psi
+/- 500 psi. If back pressure in the grease line exceeds the preset limit, grease will then be expelled from
this valve to reduce risk of motor overload and limit excessive grease pressure in grease hose. Do not
exceed specifications or alter gun to perform beyond ratings. Such misuse will void the warranty and can
cause possible injury.
WARNING: Do not adjust or remove pressure relief valve.
Assembly
BULK LOADING:
• Remove grease barrel from pump head assembly.
• Insert the open end of the grease barrel into lubricant in bulk container. Slowly pull the follower handle
back while pushing the grease barrel deeper into the lubricant to prevent air pockets from being pulled
into the grease barrel assembly.
• When the follower rod is fully extended, pull it sideways to latch the rod notch into the slot in the grease
barrel end cap.
• Assemble the grease barrel into the pump head. Release the follower rod from slot. Push the follower
rod into the grease barrel.
• Follow priming instructions below.
FILLER PUMP LOADING (Using Optional Filler Nipple: Part #L2461 - Not Included):
Replace the plug in the head of the grease gun with a 1/8" MNPT filler nipple for loading with a
manually-operated grease transfer pump. Follow filler pump instructions also.
• Insert the gun filler nipple into the filler pump socket.
• Operate the filler pump to fill the grease barrel. When the follower rod can be pulled out without effort
and the rod notch is exposed, the grease barrel is filled. The follower rod will be extended approximately
8" (20.3 cm)
• Push the follower rod into the grease barrel assembly.
• Follow priming instructions below.
PRIMING:
• Release follower rod and push rod up
• Press Automatic Bleeder Valve to expel air
• Pull trigger until grease flows without air
OPERATION
DANGER: Never operate product in an explosive atmosphere. Electric power tools and battery powered tools can create sparks, which
may ignite flammable liquids, dusts, or fumes.
• DANGER: Because of the high working pressures developed by this gun, the possibility of grease injection into the flesh, or an eye, is a
potential hazard. Never allow any part of the human body to come in front of, or in direct contact with a grease discharge outlet or potential
hose rupture. Never point the nozzle of the gun at yourself or toward anyone else. If accidental grease injection should occur, seek
Immediate Emergency Medical Attention. DO NOT try to treat the injury yourself! If injection occurs, provide grease product information to
medical personnel. Be certain that any and all system components will withstand the pressures being developed. Never exceed the
pressure rating of any component in the system. Inspect all hoses and fittings before each use.Weak, worn, or damaged hoses are a
hazard. Do not use any defective, unmarked, or damaged hoses. Do not repair the grease whip hose. Replace if damaged.
• WARNING: Grease gun can develop high pressure – up to 7000 psi (483 bar). Use safety glasses and gloves for protection during
operation. Keep hands clear of the exposed rubber or plastic portion of hose. Extreme pressure may cause nozzle extension or grease
hose to burst.
• CAUTION: Inspect and tighten all fluid connections regularly and replace weak or damaged hoses or other components with suitable
replacements that will withstand the pressures developed.
• CAUTION: Release trigger if blocked line causes grease gun to stall. Continued operation could damage the motor.

CHARGER OPERATION:

The battery pack is not fully charged out of the carton. Read and understand all of the safety instructions, and then follow the battery
charging instructions that follow.
Figure 1
Automatic Air Bleeder
Figure 2
Shoulder Strap
Figure 3
Hose Dock
Figure 4
Pressure Relief Valve