Virutex AS382L Manual De Instrucciones página 6

switch H (Fig. 5) into position "II". Once in this position,
when the trimmers of edgebander EB35 are working,
the dust collector will automatically switch on, and will
continue to function for approximately 5 seconds after
the trimmers have stopped.
Never connect edgebander to supplemen-
tary socket G (Fig. 5) of the dust collector.
7. DRY SUCTION / OPERATING INSTRUCTIONS
- Insert the filters A and B (Fig. 1 and 2). If a paper filter
bag is used, install only the cartridge for filter B (Fig.2).
- If a paper bag is provided, insert it in the tank on
the deflector.
- Assembly the head on tank and block it by hooks K,
(Fig. 1).
- Connect the flexible E hose to the inlet C (Fig. 1).
- Connect the plug to a power socket and turn switch
H (Fig. 5).
8. LIQUID SUCTION /
OPERATING INSTRUCIONS
- Remove the filters A and B (Fig. 1 and 2)
- Assembly the head on tank and block it by hooks K
(Fig. 1).
- Connect the flexible E hose to the inlet C (Fig. 1).
- Connect the plug to a power socket and turn switch
H (Fig. 5).
If you wish to use the machine for dust collection again,
the filters must be replaced in their original positions.
Never use the dust collector for decanting
flammable liquids.
If any liquid or foam leaks out of the
appliance, switch off the electrical supply
emmediately.
9. USE WITH POWER TOOLS
Before using the dust collector ensure:
- That the filter A (Fig. 1), is correctly inserted inside
the aspirator. If you use a paper dust bag check that
it is correctly fitted.
- That the supplementary filter B (Fig. 1) is correctly
inserted in the upper part of the body.
Next:
- Connect the aspiration tube to vacuum opening C (Fig.
4) and to the socket on the electric tool.
Connect the plug of the tool to the supplementary socket
G (Fig. 5) on the upper part of the dust collector head.
Connect the dust collector plug to the mains and turn
6
switch G (Fig. 5) to position "II". In this way, each time
the tool is used, the dust collector will also switch on
automatically.
- If, on connecting a electronically regulated portable
machine to the dust collector, you should notice that
the dust collector does not start up automatically when
the machine is turned on, just turn the connection plug
of the machine in the dust collector through an angle
of 180° to rectify the problem.
- With accessory 8299173 Y-Connector D. 32, it is possible
to use up to two different tools simultaneously with the
same dust collector.
10. INSTRUCTION TO BE STRICTLY FOLLOWED
• The use of this machine for anything not specified in
this manual may be dangerous and must be avoided.
• The suction nozzle should be kept away from the body,
especially delicate areas such as the eyes, ears and mouth.
• The equipment should be correctly assembled before
use.
• Ensure that power sockets used are correct for the
machine.
• Check the voltage indicated on the rating plate is the
same as the supply voltage.
• These machines are not designed for picking up health
eddangering dusts or inflammable/esplosive substances.
• Never leave the equipment unattended whilst in use.
• Never carry out any maintenance on the machine
without first disconnecting from the mains supply, if
the machine is to be left unattended or can bereached
by childrens or others persons not aware about their
action, the supply should also be terminated.
• The main supply cable should not be used to pull or
lift the machine.
• The machine should never be emersed in water or a
pressure jet of water used for cleaning.
• Periodically examine the mains cable and machine for
damage. If any damage is found contact your service
centre for repair.
• Should extension cables be used, ensure that the cable
rating is suitable for use with the equipment.
Do not use the cable coiled as this could result in a voltage
drop or overheating. Keep dry at all times.
• The equipment should not be used to pick up water
from containers lavatories, tubs, etc.
• Ensure that the float (Fig. 4) is not damaged or obs-
tructed by anything that may stop it from rising. The
floats function is to stop the suction when the tank
is full or if the machine should overturn accidentally.
• If the equipment should overturn it is recommended
that the machine should be stood up before switching off.
• If foam / liquid should come from the machine exhaust
switch off immediately.
• Aggressive solvents or detergents should not be used.
• The manufacturer cannot be held responsible for any
damage/injury caused to persons or property, because of