Before Taking A Measurement; Changing Temperature Scales; Error Messages - JBM AET-R1B1 Manual De Instrucciones

REF. 53794

BEFORE TAKING A MEASUREMENT

Try the device by yourself first to know how to
1.
use it.
2. It must be placed in a general environment of
room temperature of 16ºC-35ºC for at least 30
minutes before use to avoid incorrect measure-
ment results.
3. The person measured should be kept at room
temperature for at least 20 minutes to make body
temperature balanced.
4. After strenuous exercise, you should rest for at
least 30 minutes before taking measurement.
5. Wipe the skin dry and push aside hair strands
before commencing.
6. When repeated measurements are made con-
tinuously, move away the probe between each
measurement and rest for at least 5s before ma-
king the next to obtain the most correct result.
7. The normal
35.5ºC∼37.8ºC. The user should take more tem-
perature to know his or her own health tempera-
ture. Pay attention to physical changas or consult
your doctor if there is any abnormality.
8. Check the probe is clean before each measure-
ment to ensure accuracy.
RECALLING READINGS FROM MEMORY
Ensure the thermometer is switched off.
1.
2. Press the "ON/OFF/MEASURE" button for 4 se-
conds to put the device on memory mode. The
last reading will be displayed.
3. Press and release the "ON/OFF/MEASURE" but-
ton again to display the next reading in a sequen-
ce from the last reading to the first reading.
4. The thermometer has memory to recall the last
32 readings.
The thermometer will automatically turn off if it
5.
idles for more than 12 seconds.

CHANGING TEMPERATURE SCALES

Ensure the thermometer is switched off.
1.
2. Press the "ON/OFF/MEASURE" button for 8 se-
conds to bring it into temperature mode. The cu-
rrent temperature unit will be displayed.
3. Release and press the ON/OFF/MEASURE but-
ton again to toggle and select between ºC and ºF.
The thermometer will switch off automatically if
4.
it idles for more than 4 seconds and will display
the last reading
WARNING!
• Do not use the thermometer under extreme tem-
peratures (below 16ºC/60.8ºF or over 35ºC/95ºF)
or humidity extremes (below 15%RH or over
80%RH).
• Do not use the thermometer under extreme tem-
peratures (below -20ºC/-4ºF or over 55ºC/131ºF)
or humidity extremes (below 15%RH or over
93%RH).
• If temperature probe has been shocked and lux,
contact your retailer immediately.
• lt is dangerous for patients to perform a self-eva-
reading value is about
luation and self-treatment based on the measu-
ring results. Be sure to follow doctor's instruction.
• Do not touch or blow infrared sensor.
• Clean a polluted infrared sensor with a soft dry
cloth in a gentle manner. Cleaning with toilet tis-
sue or paper towel may scratch the infrared sen-
sor, causing inaccuracy.
• Install the battery in the right position according
to the manual.
• Do not immerse the thermometer in liquids, this
device is not waterproof.
• Do not use a mobile phone nearby when the ther-
mometer is working.
• If the probe glass is damaged, stop using it and
contact your retailer immediately.
• Do not modify the device.
• The device is not repairable and contains no user
serviceable parts.
• The device requires no calibration.
If the device is modified, appropriate inspection
•
and testing must be conducted to ensure conti-
nued safe use of the equipment.
• The operator shall not touch the thermometer
and the patient simultaneously.
• Keep the device out of children's reach.
For temperature difference between storage area
•
and measurement site, condition the thermome-
ter for about 30 minutes in room temperature.
• Ensure that children do not use the instrument
unsupervised. Some parts are small enought to
be swallowed.
• No servicing/maintance white the MW equipment
in use.
• The patient can measure data and change bat-
tery under normal circumstances,
• The patient can maintain the device according to
the user manual.

ERROR MESSAGES

Error Problem
message
Temperature is
higher than 42.2°C
(108°F).
Hi
Temperature is
lower than 32 °C
(89.6 °F).
Lo
Err Sensor not welded.
Low power.
The temperature
of the measuring
ErH
environment is too
high.
The temperature
of the measuring
ErL
environment is
too low.
· 9 ·
Solution
Operate the thermometer
only between the specified
temperature ranges. In the
event of a repeated error
message, contact your
retailer.
Operate the thermometer
only between the specified
temperature ranges. In the
event of a repeated error
message, contact your
retailer.
Contact your retailer.
Replace new batteries.
Decrease the temperature
of the environment, keep it
within 16°C-35°C.
Increase the temperature
of the environment, keep it
within 16°C-35°C.