PURE 72322 Manual De Usuario

Pure Bluetooth Earbuds
72322
User Manual
Specification
Bluetooth version: 4.2
Battery: 110 mah
Music play time: up to 5 hours
Talk time: up to 5 hours
Standby time : up to160 hours
Charging time: up to 2 hours
Charging Voltage: DC 5V
Bluetooth operating distance
up to 30 FT
Driver:Stereo,Φ10mm,32Ω
Rated/Max Power:20mW/30mW
Sensitivity: 99dB 3dB
Frequency Response: 50~20KHz
Power ON/OFF & Reconnecting
· To turn on the PURE Earbuds press the power button for
approximately 2 seconds. You will see a blue light flash on the
side of the left earbud 4 times meaning the unit is powered up.
The earbud will also verbally say that it is powered on.
· To turn off the PURE Earbuds press the power button for
approximately 2 seconds. You will see a red light flash and then
the earbuds will verbally say "power off".
· Note these earbuds will automatically connect to the last
smart phone/device they were connected to when powered on
again.
Pairing the PURE Earbuds
· Turn on the Bluetooth function on your smart phone or device.
· To pair your PURE Earbuds hold down the power button (from
the off state) for approximately 2 seconds from off state. The left
earbud will flash red/blue meaning that it is in pairing mode. Find
the device named "PURE" under the list of pairing devices on
your phone. Once the earbuds are paired the LED light will flash
blue continuously.
· Note the Bluetooth ® pairing password is "0000". Most phones
will enter this in automatically. Only certain phones will require
you to enter this code in manually.
WIRELESS PAIRING
2
Earbuds are in pairing mode
when LED flashes blue/red
2
Charging the PURE Earbuds
· Connect the charging cable to the Micro USB charging port on
the bottom of the left earbud. Then connect to micro USB cable
to a USB power source such as a laptop or an AC charger. The
approximate charge time is 2 hours for a full charge.
· Note the red light will remain on when charging the earbuds.
· Once the battery is fully charged the light will turn to blue.
· On a full charge these earbuds will provide up to 5 hours of
music play time, up to 5 hours of talk time and up to 160 hours
of standby.
Music/Tracking Control/ Volume Control
· To adjust the volume press either button with a triangle shown
in the image below that is located on the microphone.
· To "Forward" to the next song, hold down the top triangle
button on the microphone for 2 seconds.
· To "Go back" to the previous song, hold down the down
triangle button on the microphone for 2 seconds.
Answering/Ending Phone Calls
· To answer or end a phone call press the middle square button
on the microphone. Note that if you are listening to music the
phone call will pause the song and when you end the call it will
resume playing the song where you left off.
Trouble Shooting
POWER
If you are unable to pair your PURE Earbuds to you smart
phone/device try the following:
· Confirm that your phone's Bluetooth
· Confirm the PURE Earbuds are on and in pairing mode. The
left earbud will flash red/blue and once the pairing is complete it
will only flash blue.
If the earbuds are in pairing mode and you cannot find "PURE"
in your phone's Bluetooth
phone off and then back on along with the earbuds.
If you experience disconnecting or noise interference after
pairing try the following:
·Make sure your PURE earbuds are charged, as low battery
could affect their performance.
If you loose the Bluetooth
and your phone make sure: you are within the 30FT range and
do not cover the earbuds with your hand or other objects that
will interfere with transmission.
The red light on the earbuds does not turn on when charging:
If the earbuds have not been used for a long period of time it
will take 30 min of charging for the red light to appear. Continue
charging for 2 hours to ensure they are fully powered.
The Bluetooth® word mark and logos are registered trademarks
owned by the Bluetooth SIG, Inc. and any use of such marks by CJ Global Inc.
is under license.
Other trademarks and trade names are those of their respective owners.
LED
Produced and distributed by CJ Global Inc.
CHARGING
C har ge vi a m ic ro USB cable.
R em ove USB cable f rom t he
devi ce once LED changes
f r om red to blue.
LED
® setting is on.
® devices please turn your mobile
® connection between the earbuds
Des Earbuds de Pure
Bluetooth
Manuel de l'utilisateur
Specification
Version Bluetooth : 4.2
Batterie : 110 mah
temps de lecture Musique : jusqu'à 5 heures
Temps de conversation : jusqu'à 5 heures
Autonomie en veille : jusqu'à 160 heures
Temps de charge : jusqu'à 2 heures
Tension de charge : DC 5V
Distance de fonctionnement Bluetooth:
jusqu'à 30 FT
Chauffeur:Stereo,Φ10mm,32Ω
Rated/Puissance Max:20mW/30mW
sensibilité: 99dB 3dB
Réponse en fréquence : 50~20KHz
Allumage / hors tension et la reconnexion
· Pour activer les écouteurs sans fils PURE appuyez sur le
bouton d'alimentation pendant environ 2 secondes. Vous verrez
une lumière bleue clignote sur le côté gauche du casque 4 fois,
ce qui signifie que l'unité est sous tension. L'auriculaire
également disent oralement que est allumé.
· Pour désactiver les écouteurs PURE appuyez sur le bouton
d'alimentation pendant environ 2 secondes. Vous verrez une
lumière rouge clignotant et ensuite les écouteurs se disent
oralement "power off".
· Note : Ces écouteurs se connecte automatiquement avec le
dernier téléphone intelligent ou périphérique connecté lorsque
s'allume de nouveau.
ALLUMAGE / HORS TENSION
Appuyez sur le bouton d´alimentation/ Appuyez sur le bouton d´alimentation/
connecter pour allumer connecter pour éteindre
Le couplage d'oreillettes sans fil PURE
· Activer la fonction Bluetooth sur votre téléphone ou appareil.
· À votre paire d'oreillettes PURE maintenez le bouton
d'alimentation (à partir de l'état hors tension) pendant environ 2
secondes. L'oreillette gauche clignote en rouge/bleu qui signifie
qu'il est en mode couplage. Trouver le périphérique "PURE" sous
la liste des dispositifs de couplage sur votre téléphone. Une fois
les écouteurs sont couplés, la LED clignote en bleu.
· Remarque le couplage Bluetooth® mot de passe est "0000". La
plupart des téléphones portables va entrer dans ce
automatiquement. Seuls certains téléphones exigent d'entrer ce
COUPLAGE SANS FILS
2
Appuyez et maintenez le bouton d'alimentation Les écouteurs sont en mode
/connecter le bouton pendant 2 secondes couplage lorsque la LED clignote
pour lier dispositif
en bleu/rouge
72322
LED