Descargar Imprimir esta página

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Bottom Mount Refrigerator Dispense Guide
Water Dispenser
IMPORTANT:
� After connecting the refrigerator to a water source or replacing
the water filter, flush the water system. Use a sturdy container
to depress and hold the water dispenser pad for 5 seconds,
then release it for 5 seconds. Repeat until water begins to flow.
Once water begins to flow, continue depressing and releasing
the dispenser pad (5 seconds on, 5 seconds off) until a total of 4
gal. (15 L) has been dispensed. This will flush air from the filter
and water dispensing system, and prepare the water filter for
use. Additional flushing may be required in some households.
As air is cleared from the system, water may spurt out of the
dispenser.
NOTE: After 5 minutes of continuous dispensing, the dispenser
will stop dispensing water to avoid flooding. To continue
dispensing, press the dispenser pad again.
� Allow 24 hours for the refrigerator to cool down and chill water.
Dispense enough water every week to maintain a fresh supply.
Dispensing Water
1. Hold a container under the dispenser spout while pressing the
dispenser pad.
2. Release the dispenser pad to stop dispensing.
Ice Maker
IMPORTANT: Flush the water system before turning on the ice
maker. See "Water Dispenser."
Turning the Ice Maker On/Off
� To turn the ice maker On, simply lower the wire shutoff arm.
� To manually turn the ice maker off, lift the wire shutoff arm to the
off (arm up) position and listen for the click.
NOTE: Your ice maker has an automatic shutoff. As ice is made,
the ice cubes will fill the ice storage bin and the ice cubes will raise
the wire shutoff arm to the Off (arm up) position. Do not force the
wire shutoff arm up or down.
NOTE: Turn off the ice maker before removing the ice storage bin
to serve ice or to clean the bin. This will keep the ice cubes from
dropping out of the ice maker and into the freezer compartment.
After replacing the ice storage bin, turn on the ice maker.
Ice Production Rate
� The ice maker should produce a complete batch of ice
approximately every 3 hours.
� To increase ice production, lower the freezer and refrigerator
temperature, or see "Control Panel Descriptions" in the Quick
Start Guide for details. Wait 24 hours between adjustments.
Remember:
� Allow 24 hours to produce the first batch of ice. Discard the first
three batches of ice produced. Allow 3 days to completely fill
the ice storage bin.
� The quality of your ice will be only as good as the quality of the
water supplied to your ice maker. Avoid connecting the ice
maker to a softened water supply. Water softener chemicals
(such as salt) can damage parts of the ice maker and lead to
poor quality ice. If a softened water supply cannot be avoided,
make sure the water softener is operating properly and is well
maintained.
� Do not store anything on top of the ice maker or in the ice
storage bin.
1

Publicidad

loading

Resumen de contenidos para Whirlpool W11412396A

  • Página 1 Bottom Mount Refrigerator Dispense Guide Water Dispenser Ice Maker IMPORTANT: IMPORTANT: Flush the water system before turning on the ice maker. See “Water Dispenser.” � After connecting the refrigerator to a water source or replacing the water filter, flush the water system. Use a sturdy container Turning the Ice Maker On/Off to depress and hold the water dispenser pad for 5 seconds, �...
  • Página 2 Guide de distribution du réfrigérateur avec congélateur en bas Distributeur d’eau Machine à glaçons IMPORTANT : IMPORTANT : Purger le système d’approvisionnement en eau avant de mettre en marche la machine à glaçons. Voir la section � Après avoir raccordé le réfrigérateur à une source «...
  • Página 3 � No guarde nada encima de la fábrica de hielo o en el depósito de hielo. ® ©2020 Whirlpool. All rights reserved. Used under license in Canada. ™ Tous droits réservés. Utilisé sous licence au Canada. Todos los derechos reservados. Se usa bajo licencia en Canadá.