SMART-HOUSE BH8-RE20A4-230 Manual Del Usario

GB Specifications
Output Specifications
Outputs 4 SPST relays
Contact ratings (AgSnO2) µ (micro gap)
Resistive loads AC1 20 A
In-rush current 120 A (20 msec.)
Max. switching voltage 440 VAC
Max. switching power 10 kVA
Capacitive load ≤ 200 µF
Lamp load ≤ 4800 W
Switching operations ≥ 60000 operations
Minimum load 100 mA/12 V
Max. Switching Frequency 2 Hz
Response time ≤ 1 pulse train
Supply Specifications
Power Supply Overvoltage cat. III
(IEC 60664)
Rated operational voltage
Through term. 21 & 22 230 VAC, +/- 10%
(IEC 60038)
Frequency 45 to 65 Hz
Rated operational power Typ. 2,5 VA
Max. power dissipation 7 W
Rated impulse withstand volt.
230 4 kV
Dielectric voltage
Supply – smart-house ≥ 4 kVAC (rms)
Supply – Outputs ≥ 4 kVAC (rms)
Outputs – smart-house ≥ 4 kVAC (rms)
General Specifications
Fail polarity state delay
Upon loss of smart-house carrier ≤ 20 ms
Power ON delay typ. 2s
Indication for:
Supply ON LED, Green
smart-house carrier LED, Yellow
Output ON LED, Red (one per output)
Environment
Degree of protection IP 20
Pollution degree 3 (IEC 60664)
Operating temperature - 5 to +50°C (+23° to +122°F)
Storage temperature -50 to +85°C (-58° to
+185°F)
Humidity (non-condensing) 20 to 80%
Mechanical resistance
Shock 5 G (11ms)
Vibration 2 G (6 to 55Hz)
Housing H8-housing
Weight 500 g
Mode of Operation
4-channel receiver with 4 normally open contact outputs. Each
output is individually coded by means of the code programmer
BGP-COD-BAT. For changing the default setting, please refer to
the datasheet on BGP-COD-BAT.
The outputs are normally OFF. When a transmitter coded to the
selected channel is activated, the output turns ON and remains
ON until the respective channel becomes deactivated. The
default setting is such that upon loss of smart-house carrier, all
the outputs go OFF. If fail polarity is set to 1, the relays will go
on upon loss of carrier.
On the front of the module, it is possible to override each relay
mechanically. The LEDs will not follow manual override. The
manual override will be reset if smart-house or power is put
off and on in min. 10 seconds. Each relay is labled so that it is
possible to see the relay's actual status.
Note: At delivery some of the relays might be ON due to trans-
portation bumps. To be sure that the relays are OFF, connect
the module to power and smart-house and transmit on chan-
nels A1-4 once.
Note: Due to the construction with bistable relays, the
module is intended for heating and light control only.
Dimensions
Dimensiones / Dimensjoner
Wiring Diagram
Diagrama de conexiones / Koblingsskjema
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
1 2
21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36
out out
1 2
Power
supply
User Manual
Manual del Usario
Brukerveiledning
Over Hadstenvej 40, DK-8370 Hadsten
Phone +45 89606100, Fax +45 86982522
D+
D-
3 4
out out
3 4
Output Module 4 x 20 mp
BH8-RE20 4-230
Módulo de salida 4 x 20 amperios /
Utgangsmodul 4 x 20 mp
ertified in accordance with ISO 9001
Empresa que cumple con ISO 9001
Sertifisert i henhold til ISO 9001
MAN BH8-RE20A4-230 rev 15 09.2009