Troy-Bilt XP Serie Guia De Inicio Rapido

WARNING Failure to read and follow the operator's
manual and all operating instructions could result in
death, serious injury, and/or property damage.
WARNING Fuel and its vapors are extremely flammable
and explosive which could cause burns, fire or
explosion resulting in death, serious injury and/or
property damage. Turn generator engine OFF and let
it cool at least 2 minutes before removing fuel cap. Let spilled
fuel evaporate before starting engine. Always allow space for
fuel expansion.
WARNING Contact with muffler area could cause burns
resulting in serious injury. DO NOT touch hot parts
and AVOID hot exhaust gases.
You Will Need:
• Utility knife • Pliers • Two 13 mm wrenches • 8 mm or 5/16 in. socket wrench • Safety glasses
• Unleaded fuel • Adjustable Wrench
Unpack Generator
1.
Set the carton on a rigid, flat surface.
2.
Remove everything from carton except generator.
3.
Open carton completely by cutting each corner from top to bottom.
4.
Ensure you have all included items prior to assembly. If items are damaged
or missing, call 1-888-611-6708.
5.
Leave generator on carton to install the wheel kit.
Install Wheels and Attach Support Legs
NOTICE Wheels and support legs must be attached prior to adding any fuel.
1.
Tip generator so that engine side is down. Tip generator back slightly and
slide narrow end of one of the support legs under engine recoil.
NOTICE Be sure to slide support leg far enough under engine recoil to prevent
generator from tipping over.
2.
Slide axle (A) through holes in generator frame.
1
3.
Slide a black nylon washer (B) over axle.
1
4.
Slide a wheel (C) over axle.
1
NOTICE Be sure to install wheel with raised hub inboard.
5.
Slide a washer (D) over axle.
1
6.
Place an e-ring (E) in axle groove.
1
7.
Install e-ring with pliers, squeezing from top of e-ring to bottom
of axle.
CAUTION E-rings could cause eye injury. E-rings could spring back
and become airborne when installing or removing, resulting in
moderate injury. Always wear eye protection when installing/
removing e-rings.
8.
Place hub cap (F) into center of wheel and push until it snaps into place.
9. Repeat steps 3 through 8 to secure second wheel.
10.
Tip generator back slightly and remove support leg from under engine recoil.
11.
Line up holes in support leg (G) with holes in generator frame.
12.
Attach support leg using two capscrews (H) and two hex nuts (I). Tighten
with 13 mm wrenches.
2
13.
Repeat step 11 and 12 to secure second support leg.
14.
Attach cord wrap posts (J) to generator frame. Tighten with an adjustable
wrench.
3
15.
Return generator to normal operating position (resting on wheels).
Attach Negative Battery Cable
WARNING Battery posts, terminals and related accessories contain lead
and lead compounds - chemicals known to the State of California to cause
cancer and reproductive harm. Wash hands after handling.
1.
Cut off tie wrap securing loose end of negative (black) cable.
2.
Using an 8 mm or 5/16 in. socket wrench, remove screw (K), lock washer
(L) and flat washer (M) on negative battery terminal.
3.
Slide lock washer, flat washer and negative battery cable (N) over screw as
shown.
4
4. Reattach screw to negative battery terminal and tighten.
5.
Verify that connections to battery and generator are tight and secure.
Attach Extend-a-panel™
1.
The Extend-a-panel™. can be connected to the generator directly or with the
provided 20 Amp, 25 ft. accessory cord. To connect the Extend-a-panel™
directly to the generator, follow these instructions:
2.
Twist knob (O) on main panel to horizontal position.
3.
Place hole at top of Extend-a-panel™ (P) over knob on main panel.
4.
Twist knob (O) to vertical position to lock Extend-a-panel™ (P) onto main
panel.
6
5.
Connect the Extend-a-panel™ twistlock (Q) to small cord under main panel
on generator.
7
6.
Connect Extend-a-panel™ two pin connector (R) to small two pin connector
cord under main panel on generator.
7
7.
Refer to Operator's Manual for use of the Extend-a-panel™ accessory cord.
© 2011 Briggs & Stratton Power Products Group, LLC. All rights reserved.
Every effort has been made to ensure that the information in this document is accurate and correct. However, we reserve the right to alter or otherwise improve the product and this document at any time without prior notice and without incurring obligation.
*This generator is rated in accordance with CSA (Canadian Standards Association) standard C22.2 No. 100-04 (motors and generators).
Quick Setup Guide
WARNING Running engine gives off carbon monoxide, an
odorless, colorless, poison gas. Breathing carbon
monoxide could result in death, serious injury,
nausea or fainting. Operate this product ONLY
outdoors. DO NOT operate this product inside any building or
enclosure, even if windows and doors are open.
WARNING Generator voltage could cause electrical shock
or burn resulting in death or serious injury. DO NOT
operate under wet conditions
Items Included:
Operator's Manual (Not Shown)
1
B
A
2
G
H
3
1
4
2
N
5
O
4
6
O
P
5
6
7
R
7000 Watt* Generator
Moving Generator
1. Remove handle pin (S) from bracket on right side of handle (viewing
generator from engine end.
2.
Pull folding handle to the upright position until latch (T) locks into place.
3. Reinsert handle pin in bracket on right side of handle.
WARNING Body Crush/Tip Over Hazard. Generator could tip over while
moving resulting in serious injury and/or property damage. Handle
pin must be installed prior to moving generator.
4. Place your foot onto the axle (U) located under the recoil starter and pull
back on the handle.
10
5.
Always face generator and push or pull to desired location. When moving
generator on an incline, always make sure you are uphill from generator.
6.
Place foot on axle and gently let generator tip forward to rest on support leg.
7.
Remove handle pin from right side of handle.
8.
Pull up on latch and push handle forward to fold down handle.
Add Engine Oil Level and Fuel
NOTICE Be sure you have attached wheels and support leg prior to this step.
NOTICE DO NOT use unapproved gasoline such as E85.
NOTICE DO NOT mix oil in gasoline.
NOTICE DO NOT modify engine to run on alternate fuels.
1.
Move generator outdoors to a flat, level surface.
2.
Clean area around oil fill (
3.
Using oil funnel (optional), slowly pour contents of provided oil bottle into
oil fill opening to the "Full" mark on dipstick.
4.
Replace oil fill cap/dipstick and fully tighten.
5.
Clean area around fuel fill cap (
6.
Slowly add unleaded gasoline (V) to fuel tank (W). Be careful not to fill above
the baffle (X). This allows adequate space for fuel expansion as shown.
7.
Install fuel cap and let any spilled fuel evaporate before starting engine.
Move Generator to Safe Operating
Location
C
D
F
E
1.
Move generator outdoors to a flat, level surface, in an area that will not
accumulate deadly exhaust gas. DO NOT place generator where exhaust gas
could accumulate and enter inside or be drawn into a potentially occupied
building. Ensure exhaust gas is kept away from any windows, doors,
ventilation intakes, or other openings that can allow exhaust gas to collect
in a confined area. Prevailing winds and air currents should be taken into
consideration when positioning generator.
2.
To reduce the risk of exhaust heat or exhaust gases igniting nearby
combustible material, keep at least 5 ft (1.5 m) clearance on all sides of
generator, including overhead.
Start Generator
I
NOTICE Always unplug the battery float charger before starting the generator.
1.
Make sure unit is on a level surface. Disconnect all electrical loads from the
generator.
2.
Turn the fuel valve (Y) to the "On" position.
J
3.
Set on/off switch (Z) to on "I" position.
4.
Pull choke handle (AA) out to choke (
For electric starting, push and hold the start switch (BB) in "Start" position
until generator starts. To prolong the life of starter components, DO NOT hold
start switch in "Start" position for more than 5 seconds, and pause for at least
1 minute between starting attempts. When engine starts, proceed to step 5.
NOTICE If battery is discharged, use manual starting instructions.
For manual starting, grasp recoil handle and pull slowly until slight resistance is
felt. Then pull rapidly one time only to start engine.
M
L
5.
As the engine warms up, gradually push choke handle in to run (
K
position.
6.
If engine does not start, refer to operator's manual for detailed starting
instructions.
Plug in Items to be Powered
1.
Let engine stabilize and warm up for a few minutes after starting.
WARNING Damaged or overloaded electrical cords could overheat, arc,
and burn resulting in death, serious injury, and/or property damage.
ONLY use cords rated for your loads. Follow all safeties on electrical
cords. Inspect cord sets before each use.
2.
Ensure rocker switch circuit breakers (CC) on main panel are in "On"
position.
16
3.
Plug in and turn on the desired 120 Volt (DD) and/or 240 Volt (EE) AC,
single phase, 60 Hz electrical loads.
4.
If using the 25 ft. (7.6 m) accessory cord with the Extend-a-panel™ always
make sure to follow all safeties and instructions on cord.
NOTICE When plugging into the 120 Volt (DD) receptacles, plug items to be
powered in sequence as shown.
NOTICE Exceeding generators wattage/amperage capacity can damage generator
and/or electrical devices connected to it.
5.
Refer to Do Not Overload Generator section of Operator's Manual.
Shut Down Generator
1.
Turn OFF and unplug all electrical loads from generator panel receptacles.
NEVER start or stop engine with electrical devices plugged in and turned ON.
2.
Let engine run at no-load for several minutes to stabilize internal
temperatures of engine and generator.
3.
Set on/off switch (Z) to off "O" position.
4.
Move fuel valve (Y) to "Off" position.
5.
To prepare for storage, refer to Operator's Manual.
Q
Have Questions?
Do not return to store. We can help.
Call Customer Service Toll-Free 1-888-611-6708
or visit our website, www.troybilt.com
8
8
9
9
10
), remove yellow oil fill cap/dipstick.
11
), remove cap.
12
13
11
12
14
13
14
15
16
) position.
16
16
)
15
16
16
16
16
15
S
T
U
W
TANK
X
V
FUEL
Exhaust Port
Pointed away from
dwelling openings
Y
Z
1
3
2
4
AA
CC
BB
DD
EE