V2 DEC-4 Manual Del Usuario página 5

DEC4 is necessary to interface the control device (TTNC / SIRMO-DEC /
SIRMO-DGC / VRD / PROKSIMA) to any control unit of V2 or other
companies automation systems.
• It is possible to store up to 240 different codes with self-learning mode.
• It is also available in the PLUS version, which can store up to 1008
different codes
• Three different functions can be programmed by means of SW1 key
for the outputs: monostable, bistable and timer.
• It is possible to enable or disable the ROLLING CODE mode.
• Memory full warning: the receiver blinks 15 times.
• It can be connected to the PROG2 portable programmer (version
3.6 or newer), which allows to manage devices by means of
WINPPCL (version 3.0 or newer)
CAUTION: before inserting the receiver into the relevant TX
connector of the PROG2, make sure that it is not powered.
WARNING: Do not install the device outside!
PROGRAMMING OF THE MONOSTABLE FUNCTION
Select the desired channel in accordance with the following table:
N°IMPULSES SW1
SELECTED CHANNEL
CHANNEL 1 MONOSTABLE
CHANNEL 2 MONOSTABLE
CHANNEL 3 MONOSTABLE
CHANNEL 4 MONOSTABLE
• Press the SW1 key of the receiver N times, as indicated above: the
relevant led goes on.
• Transmit the code by means of the control device within 5 seconds.
• The led of the receiver goes out and goes on again: the code was
stored and the receiver keeps waiting for 5 secs for a new code to
memorize.
PROGRAMMING OF THE TIMER FUNCTION
To memorize the TIMER function on the first channel, proceed as follows:
1. Press and keep pressed the SW1 button of the receiver : the led L1
(relating to the first channel) lights up for a few seconds.
2. When led L1 goes off, release the SW1 button. Led L1 starts a
sequence of flashings at low speed (1 flash per second).
The number of flashing corresponds to the time which can be set
as shown in the table.
3. Count the number of led L1 flashings corresponding to the time you
wish to set. Press the rx button SW1 during the wished flashing: the
sequence of flashings stops and led L1 remains on.
4. Transmit the code by means of the control device within 5 seconds.
5. The led of the receiver goes out and goes on again: the code was
stored and the receiver keeps waiting for 5 secs for a new code to
memorize.
To programme channels no. 2, 3 and 4, repeat the above mentioned
steps no. 2, 3 and 4, taking into consideration leds L2, L3 or L4 in
accordance with the selected channel.
N° Flashing Time N° Flashing Time
1
01 sec. 12
2 02 sec. 13
3
03 sec. 14
4
04 sec. 15
5
05 sec. 16
6
06 sec. 17
7 07 sec. 18
8
08 sec. 19
9
09 sec. 20
10
10 sec. 21
11
11 sec. 22
LED ON
L1 L2 L3 L4
•
1
•
2
•
3
•
4
N° Flashing Time
12 sec. 23 4 min.
13 sec. 24 4,5 min.
14 sec. 25 5 min.
15 sec. 26 5,5 min.
30 sec. 27 6 min.
1 min. 28 6,5 min.
1,5 min. 29 7 min.
2 min. 30 7,5 min.
2,5 min. 31 BISTABLE
3 min.
3,5 min.
PROGRAMMING OF THE BISTABLE FUNCTION
To memorize the bistable function on the first channel, proceed as
follows:
1. Press and keep pressed the receiver SW1 button : led L1 (relating
to the first channel) lights up for a few seconds.
2. When led L1 goes off, release SW1 button; led L1 starts flashing at
low speed (1 flash per second). When the 30 flashings of the timer
function are over, led L1 remains on.
3. Transmit the code by means of the control device within 5 seconds.
4. The led of the receiver goes out and goes on again: the code was
stored and the receiver keeps waiting for 5 secs for a new code to
memorize.
To programme channels no. 2, 3 and 4, repeat the above mentioned
steps no. 2, 3 and 4, taking into consideration leds L2, L3 or L4 in
accordance with the selected channel.
ROLLING CODE MODE
It is possible to activate or disable the ROLLING CODE mode.
Its activation makes any attempt of code duplication impossible.
To activate the ROLLING CODE function it is necessary to act on the
Dip-switch 2 on the printed circuit:
Dip 2 ON = ROLLING CODE mode activated
Dip 2 OFF = ROLLING CODE mode not activated
Enabling the Rolling Code by means of WINPPCL makes the Dip-switch 2
position ineffective.
WARNING: IF VRD / PROKSIMA IS USED AS A CONTROL DEVICE,
THE ROLLING CODE MODE HAS ALWAYS TO BE NOT ACTIVATED.
FULL CODE ERASING
To perform a full code erasing do the following:
• Turn off the power of the receiver
• Press and hold pressed the SW1 key of the receiver
• At the same time turn on the power again. The receiver LED goes
on: release the SW1 key
The memory spaces are empty and available for a new programming.
To perform a partial code erasing the PROG2 portable programmer is
required.
PROGRAMMING LOCK
The PROGRAMMING LOCK function can be done only by means of
WINPPCL. This function inhibits to programme again the receiver, either
with SW1 key or by radio. The receiver can be programmed again only
by means of WINPPCL.
WARNING! IF THE RECEIVER IS SUPPLIED BY 24 VAC-VDC, DO NOT
ACTIVE MORE THAN 2 RELays simultaneously
RELAY CONTACT
The four output relay contacts are normally open type; it is possible to
change it as normally closed type. Refering to fig. 1 connect point A with
point B and cut the trace at point C (Fig.4).
89/336/CE DIRECTIVE CONFORMITY
The DEC4 are in conformity with the provisions of the following EC
directive(s) (including all applicable amendments) and that the standards
referenced here below: EN 55022, EN 55024
Racconigi, 05/02/2010
V2 SPA legal representative
Cosimo De Falco