Technical Data - ACM TX PLUS 12 Guia De Inicio Rapido

ENGLISH
FUNCTIONING OF THE BUTTONS
UP Activates the automation GOING UP
DOWN Activates the automation GOING DOWN
STOP it stops the automation
FUNCTIONING OF THE BUTTON PROG AND
DIP-SWITCHES
The button PROG and the DIPSWITCHES program the functions of
the control units controlled by the transmitters TX PLUS 12. Read
carefully the section "PROGRAMMING OF THE FUNCTIONS" in
the handbook of the control unit or in the one of the tubular
motor with integrated electronic card.
CHANNEL SELECTION (BUTTON SELC)
By this button it is possible to select the channel to be used for
the radio transmission.
1 Press button SELC until selected the desired channel: the
corresponding led is on for some seconds
2. Press one of the buttons UP, DOWN or STOP to transmit the
control
To select all the channels at the same time press several times the
button SELC until all the leds are on.
To display the channel set, press once the button SELC.
SUN SENSOR ACTIVATION
To enable the sun sensor press at the same time for 10
seconds the keys STOP and UP
To disable the sun sensor press at the same time for 10
seconds the keys STOP and DOWN
GROUPS (BUTTON SELG)
By this button it is possible to program and select the GROUPS of
channels to be used for the radio transmission. It is possible to
store up to 8 groups of channels; stored the eighth, a new group
will replace the first one.
1. Press the button SELC until selected the first channel to link
to the group
2. Press the button SELG: the led linked to the selected channel
starts blinking
3. Press the button SELC until selected the second channel to
link
4. Press the button SELG: the led linked to the selected channel
starts blinking
5. Repeat the procedure for all the desired channels: the leds
linked are on till the end of the procedure
6. Once selected all the channels wait for the leds to switch off:
the group has been stored and it is possible to display it by
pressing the button SELG
When the groups are more than one, to select the desired group
proceed as follows:
1. Press the button SELG several times until selected the desired
group: the leds linked to the channels are on for some
minutes
2. Press one of the buttons UP, DOWN or STOP to transmit the
control
To delete all the groups stored proceed as follows:
1. Press and release the button SELG: the last group used is
displayed by the leds.
2. Press and hold the SELC key before the LEDs are turned off
3. Then, without releasing the SELC key, press and hold the
SELG key also.
4. Keep pressed both the buttons for some seconds until the
leds switch off: the groups have been deleted
REPLACING BATTERY
Replace the battery when the radio range power decrease or the
led light intensity becomes too feeble. Open the door of the
battery compartment and replace the battery respecting the
polarity shown by picture 2.
WARNING: Batteries contain pollutant elements, must be
disposed of in accordance with environmental regulations (ACM
advise to use a specific disposal system).Transmitter contains
pollutant elements too; follow the same procedure to dispose.
Should the batteries lose electrolytic substances, please replace
them immediately avoiding with care any contact with such
substances.

TECHNICAL DATA

Power supply ___________ 1 x Lithium 3V (CR2032 230mAh)
Frequency ______________ 434,15 MHz
Range in open field ______ 300 m
Max.absorption _________ < 15 mA
Dimensions _____________ 160x45x14 mm
Weight ________________ 75 g
EU DECLARATION OF CONFORMITY
The manufacturer ACM International srl with headquarters in
Via Oros 2 / g, 00071 Pomezia (Rm) Italy
declares that the products: TX PLUS 12
comply with the essential requirements established by the
following directives:
2014/53/EU
ROHS2 2011/65/CE
Pomezia, 05/04/2019
The legal representative of ACM International srl
Alfredo Lanzoni