WARNING
Study, understand and follow all instructions provided with this
product. Read these instructions carefully before installing, operating,
servicing, or repairing this tool. Keep these instructions in a safe,
accessible place.
INTENDED USE OF THE TOOL
This tool is intended to be used to install 3/32", 1/8", 5/32", 3/16" and
1/4" rivets. Do not use this tool outside of the designed intent. Never
modify the tool for any other purpose or use.
The heavy-duty riveter with long handles has many uses in the
Automotive, Marine and Industrial industries due to the fact it can
accommodate five different sizes of rivets ranging from 3/32" to 1/4"
in diameter. The different sizes can be utilized in a wide range of
applications that require the use of aluminum and/or steel rivets;
special application pop rivets can also be utilized and purchased from
a local supplier.
When choosing a rivet, be sure to consider the application and do
not substitute aluminum for steel rivets. Aluminum rivets are weaker,
tend to wear and shear as in the case of some window regulators that
exert a lot of tensional stress between the door frame and window
regulator. As a preliminary step, always size the drilled and deburred
hole size to the rivet diameter you wish to use.
Your rivet supplier can be of help if you should have a question
regarding the best rivet for a particular application. Always read the
instructions and follow the safety guidelines to avoid serious injury.
BEFORE USE
Before use, READ AND UNDERSTAND THE WARNINGS ON PAGE 1
and check the parts diagram and part number listing on page 7 to
make sure all parts are included. If any parts are missing or damaged,
please call your distributor.
Caution: To help prevent personal injury
Normal use of this product is likely to expose the user to dust and/or
microscopic particles containing chemicals known to the State of
California to cause cancer, birth defects or other reproductive harm.
Always wear appropriate safety equipment and clothing when
using this product. Study, understand and follow all instructions
provided with this product. Failure to read and follow all warnings
and operating instructions may result in damages and serious
injury or death.
(Users and bystanders).
it was designed.
the tool, or use of the tool with accessories not designed for it could
result in serious injury or death.
design for the job that you are attempting to perform.
equipped area.
position, and will not move during repair.
SHORT HEAVY-DUTY
1/4" RIVETER
1 YEAR LIMITED WARRANTY
The manufacturer warrants this product to the original user against
defective material or workmanship for a period of 1 year from the
date of purchase.
The manufacturer reserves the right to determine whether the part
or parts failed because of defective material, workmanship or other
causes. Failures caused by accident, alteration or misuse are not
covered by this warranty.
The manufacturer, at its discretion, will repair or replace product
covered under this warranty free of charge. Repairs or replacements
of products covered under this warranty are warrantied for the
remainder of the original warranty period.
The manufacturer or its authorized service representatives must
perform all warranty repairs. Any repair to the product by
unauthorized service representatives voids this warranty. The rights
under this warranty are limited to the original user and may not be
transferred to subsequent owners.
The warranty is in lieu of all other warranties, expressed or implied,
including warranties of merchantability and fitness for a particular
purpose. Some states do not allow the exclusion or limitations of
incidental or consequential damages, so the above limitations may
not apply to you.
Made in China
to Matco specifications
Do more with less. 30% shorter design with extended nose piece
provides increased access to tight areas.
Packs more power. Compound hinge design requires less effort
than traditional 1/4" riveters for setting everything from aluminum
to stainless rivets.
Easier to use. Tool-less design requires no wrench to adjust or
change the included 3/32", 1/8", 5/32" or 3/16" nose piece.
Specification:
Weight: 2.76 lbs. (1250g)
Length: 17" (440mm)
Working Stroke: 7mm
Rivet application sizes: 3/32"-1/4"
Aluminum
Steel
Stainless steel
DO NOT DISCARD – GIVE TO USER
Page 1
PRODUCT INFORMATION
3/32"
1/8"
5/32"
RV14S
3/16"
1/4"
1705190-14