Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
SE-0205 MULTI-PURPOSE ALARM W/REMOTE
PACKAGE INCLUDES:
Multi-Purpose Alarm Main Unit with two magnetic detectors...1PC
Remote Control...1PC
12V 23A Alkaline battery (for Remote)...1 PC
Warning Sticker... 2 PCS
BATTERY INSTALLATION:
Main Alarm Unit:
Remove the front battery cover by sliding it downwards.
Unscrew the water resistant cover.
Follow the polarity instructions and insert three AAA Alkaline batteries (not included).
Screw on the water resistant cover.
After the batteries are installed, the red LED will flash. The Main Alarm unit is now
prepared for the Remote Unit to learn the mutual control code.
Press either the ARM or DISARM button on the Remote unit. Three short beeps will
sound and the red LED will flash to indicate that the Main Alarm unit has successfully
learned the code.
Remote Unit:
Unscrew the back cover to insert or replace 1pc fresh DC12V battery (included) into
the battery compartment.
The red LED will turn on to indicate that the battery has been installed successfully.
Press either of the two buttons on the Remote Unit to turn OFF the red LED.
OPERATION:
Attach the alarm to the inside of your tool box, or on your window, door/gate, with the
included adhesive.
When setting up the Multi-Purpose Alarm for the first time, place the magnetic
sensors adjacent to each other. Make sure that the two sensors are not separated by
more than half an inch when the tool box/window/door/gate is closed.
After closing the tool box/window/door/gate, press the remote and wait for the
confirming beep: If one beep is heard, then the Multi-Purpose Alarm is armed. If
instead four beeps sound, then the magnetic sensors are too far apart and need to be
placed closer together. Open the tool box/window/door/gate, re-adjust the sensors,
and try again until a "beep" sound is heard. Now the Multi-Purpose Alarm is ready to
protect your valuables.
Use the remote to arm and disarm the Multi-Purpose Alarm. These actions are
confirmed by an audible beep and LED flash.
The alarm will enter into arm status 5 seconds after the ARM button is pressed.
In the event of a break-in, the armed alarm and the LED will go off continuously for
one minute and then automatically reset to armed status.
Turn OFF the alarm by pressing DISARM. Two short beeps will then sound
accompanied by an LED flash.
LOW BATTERY INDICATION:
Main Alarm Unit: When the battery power becomes low, the red LED will flash at 20
Protect virtually anything
Publicidad
Resumen de contenidos para HOMEDEPOT SE-0205
- Página 1 SE-0205 MULTI-PURPOSE ALARM W/REMOTE Protect virtually anything PACKAGE INCLUDES: Multi-Purpose Alarm Main Unit with two magnetic detectors...1PC Remote Control...1PC 12V 23A Alkaline battery (for Remote)…1 PC Warning Sticker… 2 PCS BATTERY INSTALLATION: Main Alarm Unit: Remove the front battery cover by sliding it downwards.
- Página 2 second intervals to remind the user that the batteries will need to be replaced soon. Remote Unit: If the remote distance becomes obviously shorter than average, then may indicate that the Remote unit’s battery is low and needs to be replaced. NOTES: Each time new batteries are placed in the Main Unit or the Remote, the alarm needs to re-learn the code by repeating the above steps.
- Página 3 WARRANTY COVERAGE”. DOBERMAN IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, INCLUDING WITHOUT LIMITATION, LOSS OF GOODWILL, PROFITS OR REVENUE, LOSS OF USE OF THIS PRODUCT OR ANY ASSOCIATED EQUIPMENT, COST OF SUBSTITUTE EQUIPMENT, DOWNTIME COSTS, OR CLAIMS OF ANY PARTY DEALING WITH BUYER FOR SUCH DAMAGES.
- Página 4 This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. To maintain compliance with FCC RF exposure compliance requirements, please follow operation instruction as documented in this manual. SE-0205 MULTI-PURPOSE ALARM W/REMOTE Virtualmente protege cualquier cosa PAQUETE INCLUYE: Alarma mutipleuso con dos detectores magnéticos ...1pz...
-
Página 5: Operación
Oprime cualquiera de los dos botones del control remoto para apagar el LED. OPERACIÓN: Coloque la alarma dentro su caja de herramientas, o en su ventana, puerta/portón, con el adhesivo incluido. Cuando configurando el multipleuso alarma por primera vez ponga los dos sensores magnéticos adyacentes. -
Página 6: Garantía Limitada Exclusiones Y Limites
Durante el tiempo de garantía en las piezas, no habrá cobro por las piezas. Tiene que requerir el numero de “RMA” por correo electrónico (email) después envié su producto durante el tiempo de garantía. Garantía aplica solamente a productos comprados o reparados en USA y Canadá.