Descargar Imprimir esta página

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

PRECAUTIONS
• Never use without the water seal in place:
1. The water seal is the large ring around outer
diameter of unit, located between plastic
dome and plastic base.
• Do not immerse plastic battery/motor
compartment in water.
• Do not allow unit to tip over in bird bath.
• Do not use without metal legs installed.
• Do not allow material such as algae, twigs, or
leaves to become attached to the agitator.
Such attachments will shorten battery life
significantly.
• Always keep water level at least 1/4" below the
plastic base.
• If battery/motor compartment does
become wet:
1. Open unit and remove batteries. Dry
batteries with a towel.
2. Dry battery compartment and motor using
hair dryer.
• Change batteries when unit no longer creates
waves.
• This unit will not de-ice water. Remove the
batteries and store the unit during the winter.
• Lights turn on at dusk and stay on for three
hours.
DO NOT REMOVE THE SILVER DISC
INSIDE THE COVER!
DIRECTIONS
1. Remove the dome-
shaped top from the
base by unscrewing in
a counter-clockwise
direction. Remove
the parts needed to
complete the assembly
of your unit from the
plastic bag.
2. Insert the 3 "U" shaped
wire supports into the
base of the unit (figure 1).
3. Attach the
"stirring device"
to the motor by
pressing into
place using the
center hole in
stirring device
(figure 2).
AURORA WATER WIGGLER
4. Now insert the two "D"
cell batteries (figure 3).
The "stirring device" will
begin turning once the
batteries are inserted.
Be sure to insert the
batteries in the direction
indicated on the unit.
5. Close the unit by
screwing the dome on
in a clockwise direction
until resistance is felt. Do not over tighten.
6. When the bird bath is filled completely with
water (as will happen after a heavy rain) the
highest water level must remain at least 1/4"
below the plastic bottom of the Water Wiggler.
To determine the depth of your bird bath,
empty the water in the bird bath and place
the Water Wiggler in the deepest portion of
bird bath (figure 4). Place a yardstick or other
"straight-edge" device across the top rim of the
bird bath.
A. If the maximum high-water level (simulated
by the straight- edge placed across the bird
bath) is more than 1/4" from the plastic bottom
of the Water Wiggler, simply place the unit
in the center of your bath and it is ready to
operate.
Figure 1
B. If the maximum high-water level (simulated
by the straight- edge placed across the bird
bath) is less than 1/4" from the plastic bottom
of the Water Wiggler, then you must raise
the unit by placing a stable and level support
under the Water Wiggler. Be sure the unit is
secure and will not fall off of this
raised support.
Figure 2
*Illustrations may not exactly match your unit.
Miller Manufacturing, Glencoe, MN 55336 USA • www.miller-mfg.com
Read Instructions Thoroughly Before Use
Item # 7WW
Figure 3
Figure 4
REPLACEMENT OF
STIRRING FLOATS
Float replacement (extra floats are located inside
your Water Wiggler).
1. Remove stirrer assembly from the bottom of
the Water Wiggler.
2. Pull the wire guide out of the plastic crossbar.
3. Remove the old floats and place the new floats
on the wire guide (see drawing for orientation).
3. Insert the wire guide back into the crossbar
(center hole faces away from the floats).
4. Make sure the wire guide does not protrude
past the top edge of the crossbar, and then
remount the stirrer to the Water Wiggler.
NOTE: The Wire Guide cannot
Center Hole
extend past the Crossbar.
Stirrer Assembly
Crossbar
Wire Guide
Float (2)
Note orientation
302561

Publicidad

loading

Resumen de contenidos para Miller Api 7WW

  • Página 1 Stirrer Assembly place using the center hole in stirring device (figure 2). Figure 2 *Illustrations may not exactly match your unit. 302561 Miller Manufacturing, Glencoe, MN 55336 USA • www.miller-mfg.com...
  • Página 2 à l'aide du trou se trouvant Ensemble d'agitateur Stirrer Assembly au centre du dispositif Illustration 2 d'agitation *Les illustrations pourraient ne pas correspondre (Illustration 2). exactement à votre unité. 302561 Miller Manufacturing, Glencoe, MN, 55336 É.U. • www.miller-mfg.com...
  • Página 3 Stirrer Assembly Conjunto del agitador agitador (figura 2). *Las ilustraciones podrían no coincidir Figura 2 exactamente con su unidad. 302561 Miller Manufacturing, Glencoe, MN 55336 EE. UU. • www.miller-mfg.com...