Front And Rear View - Vimar Eikon TACTIL 21860 Guia De Inicio Rapido

Ocultar thumbs

Tabla de contenido

Idiomas disponibles

Eikon TACTIL

21860

Home automation control device, 6 independently programmable buttons for

managing single loads or scenarios, KNX standard, to be completed with a

label and Eikon Tactil cover plate - 3 modules

The device consists of 6 independent touch buttons that, via the KNX bus, enable controlling

relay actuators, dimmer actuators and roller shutter actuators; they can also be used for calling

up scenarios. The device is to be completed with the Eikon Tactil cover plate; the buttons

however react to mechanical pressure even without fitting the cover plate so the configuration

and the first operating test can be performed in this condition.

FEATURES.

• Rated supply voltage Busbar: 30 V d.c. SELV

• Absorption from the Bus: 35 mA

• Terminals: TP BUS

• Operating temperature: -5°C - + 45°C (indoor use)

OPERATION.

• Device settings:

- colour (can be selected from a list or by setting the RGB coordinates)

- button sensitivity (i.e., the amount of pressure required to actuate a command)

- buzzer on/off

- behaviour of the LEDs with the device on standby (off or with low brightness)

• Possible functions of the buttons:

- sending ON, OFF and timed ON commands

- ON and OFF switch on the up and on the down side

- Call up and save scenario

- Send value

- Dimmer control

- Toggle

• Possible functions of the buttons with 2 associated channels:

- ON and OFF switch

- Dimmer control

- Roller shutter control

• Proximity function:

- when the user draws her hand near, the device goes into "normal" operation and the LEDs

light up brightly.

- if after 10 seconds no action is carried out, the device will go back onto standby and the

LEDs will switch off or reduce their brightness.

The illuminated icons guide the user in choosing the commands as they identify the

points where any pressure will trigger the device.

These icons can be customized with symbols and stickers to be affixed on the

corresponding buttons (art. 21847).

• Cover plate cleaning function: the device recognizes simultaneously pressing multiple keys

due to wiping with a cloth so no actions are carried out unless you dwell too long on the same

area of the cover plate.

CONFIGURATION.

The configuration of the device, physical address and parameters takes place through the ETS

software.

If the device is loaded with an incorrect ETS application, the red LED will flash ("device type"

error).

To restore the desired configuration, load the device with the correct ETS application.

All the updated ETS databases can be downloaded from the "Software di prodotto" (Product

Software) section of the website www.vimar.com

INSTALLATION RULES.

• Installation should be carried out by qualified staff in compliance with the current regulations

regarding the installation of electrical equipment in the country where the products are

installed.

• The device can be installed on Eikon Tactil cover plates with 3 and 4 modules.

In the case of cover plates with 4 modules use the appropriate blank module art. 21041 to

close the unused module.

• The device cannot be installed on the BS 5M cover plate (2+blank+2).

• On the same cover plate used for art. 21860 it is not possible to install touch devices powered

by mains voltage (art. 21174, 21119, 21122, 21134).

REGULATORY COMPLIANCE.

EMC directive. Standards EN 50428, EN 50491.

WEEE - Information for users

If the crossed-out bin symbol appears on the equipment or packaging, this means the product must

not be included with other general waste at the end of its working life. The user must take the worn

product to a sorted waste center, or return it to the retailer when purchasing a new one. Products

for disposal can be consigned free of charge (without any new purchase obligation) to retailers with

a sales area of at least 400 m

, if they measure less than 25 cm. An efficient sorted waste collection

for the environmentally friendly disposal of the used device, or its subsequent recycling, helps avoid

the potential negative effects on the environment and people's health, and encourages the re-use

and/or recycling of the construction materials.

49400580B0 05 1811