D&D Technologies SUREClose Instrucciones Para La Instalación

Installation Instructions
Flush Mount Models Hole diameter Min Post Size
SM AT90 S 1 9 / " (40mm) 2" (50mm)
16
57 AT90 S 1 9 / " (40mm) 2" (50mm)
16
57SF AT90 S 1 9 / " (40mm) 2" (50mm)
16
108 AT90 S 1 9 / " (40mm) 3" (75mm)
16
108SF AT90 S 1 9 / " (40mm) 3" (75mm)
16
FLUSH MOUNT MODELS - SCREW-ON
1
DETERMINE THE HANDING
Hinged from the left Hinged from the right
Fence Post Fence Post
F E N C E P O S T
F E N C E P O S T
Adjustment
Nozzles
must be Remove
on top
Gate Bracket
F R A M E
F E N C E P O S T
G A T E
G A T E
G A T E
4
FASTEN, CENTERED ON SET SCREW
90˚
90˚ 90˚
90˚
90˚
T S O P E C N E
B) Once bracket is at
desired position, firmly
90˚
tighten the set screw.
A) Back out set screw and install two
main fasteners. FIRMLY TIGHTEN.
90˚
For welding installations, general field welding
90˚
90˚
90˚
operations with suit able heat transfer controls,
clean up and rust protection procedures should
3/16" (5mm)
be followed.
See CAUTION advice on next page.
ASSEMBLE HINGE TO
7 8 REPLACE HINGE PINS AND INSERT
BRACKETS ON GATE
INTO POST
G A T E F R A M E
F E N C E P O S T
G A T E
G A T E
G A T E
90˚
Close
®
SURE
3/16" (5mm) 1 9 / " Pencil 3, 4, 5mm 18V
16
(40mm)
NOTE: If using SM hinge, always install at bottom of
gate. 57 and 108 models should be installed on top.
Use #14 countersunk fasteners.
2 3
MARKING HEIGHTS
MARK HINGE BRACKET LOCATION
GAP: 5 / "- 1 / "
16 2
(8-13mm)
Mark hinge center lines
G A T E F R A M E
Mark center lines as
guides for fastening
Brackets onto the
Gate Frame
F E N C E P O S T
F E N C E P O S T
F E N C E P O S T
F E N C E P O S T v For Swimming
G A T E
Pool Gates
in AU/NZ Flush Mount:
Support Blocks
F E N C E P O S T
F E N C E P O S T
(see Page 2) Face of gate and post
are aligned.
Ensure post is vertical in the
F E N C E P O S T
F E N C E P O S T
F E N C E P O S T
front and side elevations
F E N C E P O S T
G A T E
G A T E
G A T E
MARK TOP AND BOTTOM BRACKETS ON POST
5
Laser Level
E M A R F E T A G
7 / "-1 1 / "
8 16
(22-27mm)
Ensure drill hole will
F
clear the post wall
E T A G
thickness.
E T A G
E T A G
9
Drill 1 / " (40mm)
16
holes top and bottom
NOTE: Apply corrosion
0 ˚ 9
protection to exposed
metal surfaces.
FASTEN BRACKETS
9
10
TO FENCE POST
T S O P
0 ˚ 9
G A T E F R A M E
"
3 / (5mm)
16
Ensure face and side of gate are level. Firmly
F E N C E P O S T
tighten two main fasteners before tightening
G A T E
G A T E set screw.
G A T E
90˚
G A T E F R A M E
F E N C E P O S T
Installation Instructions
Hi-Performance Hardware
G A T E
G A T E
G A T E
Laser level
90˚
90˚
ON GATE FRAME
90˚
90˚
F E N C E P O S T
1" (25mm)
G A T E
G A T E
SURE
90˚
Gate stop must be installed when using SF models.
Gate must not be allowed to open past 90
voids warranty.
SCREW POST BRACKET ONTO HINGE
6
G A T E F R A M E
Models 57 & 108
90˚
open 180
o
180 to 90
from 85
NOT for child/pool safety gate.
G A T E
G A T E
MAINTENANCE REQUIREMENTS
NOTE: Apply grease to hinge
• Gate stop must be installed when using SF models. Gate must not be allowed to open past 90
threads to prevent water Doing so voids warranty.
from entering post. • Never use more than two (2) SureClose hinge/closers on any one gate.
90˚
E M A R F E T A G
• Remove all other types of hinges and self-closing devices.
• Always install SM hinge at bottom of gate and 57 or 108 closer on top.
• Ensure the gate does not swing through the line of the fence. Use a "gate stop" or a latch (with striker)
SET SCREW
to prevent this.
• All steel mounting brackets (gate and post) should be painted or powder coated. Spray painting is recommended.
• The anodized aluminum mounting brackets do not need finishing, but they may be painted or powder coated.
Level
E C N E F
• DO NOT powder coat the hinge/closer, but they may be painted.
• DO NOT turn the adjustment nozzles more than two (2) full rotations.
E T A G
E T A G • DO NOT unscrew nozzle past the surface of the body.
E T A G
• DO NOT remove the adjustment nozzles or disassemble these hinges at any time. Doing so voids warranty.
• Ensure the hinges are kept free of sand, ice and other debris that could impair effective operation.
90˚
CAUTION: Overheating any SureClose product during welding may cause failure and will void
warranty. To ensure threads on mounting bracket are not deformed, weld one surface at a time and alternate
0 ˚ 9
between top and bottom hinge. Finish with appropriate corrosion protection, avoiding thread contamination.
2 YEAR LIMITED WARRANTY:
For a downloadable Adobe Acrobat (.PDF) version of our 2 YEAR LIMITED WARRANTY,
go to our website at www.ddtechglobal.com
SURE
ADJUSTING THE CLOSING SPEED
F E N C E P O S T
AND FINAL 'SNAP' ACTION (108 ONLY)
G A T E
CAUTION: Sensitive adjustment, rotate MAX
V=Closing Speed
S=Final Snap Action
–
+
Turn nozzles clockwise to decrease speed & counterclockwise to
increase speed.
(S)
(V) If using a 57+57 or 108+108 combination, each closer must
have equal closing speed at all times.
Flush Mount Screw-On
Close
®
˚
. Doing so
o.
Hold-open from
o
. Self-close
o o
to 0
F E N C E P O S T
G A T E
open to and self-close from 90
* Suitable for child/pool safety gate.
˚
.
MANUFACTURED BY OL.MI
PRECISION ENGINEERING
Close
®
Hi-Performance Hardware
1 / turn at a time.
4
IMPORTANT:
Use dimple to determine how far nozzle has turned.
DO NOT turn adjustment nozzles more than 3 complete rotations.
DO NOT unscrew nozzle past the surface of the body.
CAUTION:
DO NOT remove adjustment nozzles or disassemble hinge.
Doing so voids warranty.
SF models have 5 dimples
for identification
Use flush mount latches/locks.
Flush Mount
Face of gate and
post are aligned
Models 108 and 108SF
v Swimming Pool Gates
have Final Snap Action.
AU/NZ
Models 57SF & 108SF
o
.
NO hold-open feature.
DO NOT PROP GATE OPEN.
* CAUTION: When used on swimming
pool gates, always consult local
authorities for swimming pool Codes.
AUSTRALIA: Unit 6, 4-6 Aquatic Dr, Frenchs Forest NSW 2086
USA: 7731 Woodwind Drive, Huntington Beach, CA 92647
www.ddtechglobal.com
Patented: CA 2650769; US 7900319; NZ 573211;
AU2010280342, AU2011202070
Copyright 2012 D&D Group Pty Ltd, Sydney Australia
SCOLM000015PA 10/2/14