Publicidad
Idiomas disponibles
Idiomas disponibles
ARTICLE
QUANTITE
1
2
2,3
2
4
2
5
2
6
2
7
6
8
2
9
6
10
8
11
8
12
6
13
6
14
6
15
2
16
2
17
2
18
12
19
12
20
12
21
8
1.
Remove contents from box. Verify that all parts listed are present. Check for damage. Carefully read and understand install instruc-
tions before starting.
2.
Starting at the passenger side, remove the tape that covers the front running board holes. This is located at the inner rocker panel be-
hind the front tire. (FIGURE 1)
3.
Partially thread (1) M11 plastic retainer to (1) M12 bolt/ M10 nut plate. Then place the bolt plate through the slot with the two smaller
holes below. Tighten the plastic retainer so the bolt plate is secure. (FIGURE 1)
4.
Partially thread (1) M11 plastic retainer to (1) M12 stud plate, then insert it into the most frontal slot. Tighten the plastic retainer so
the stud plate is secure. (FIGURE 2)
5.
Attach the passenger side mounting bracket to the installed stud plates using (2) M12 flat washers, (2) M12 lock washers, and (2)
M12 hex nuts. Do not tighten at this time. (FIGURE 3)
6.
Rotate the second to front M12 bolt/ M10 nut plate so the nut lines up with the rocker panel hole, and mounting bracket slot. Attach
with (1) M10 bolt with (1) M10 flat washer, and (1) M10 lock washer. Do not tighten at this time. (FIGURE 3)
7.
Unscrew the vehicle's body mount bolt located to the left of the mounting bracket. Attach (1) mount support bracket between the
body mount and body mount bolt assembly. (FIGURE 2)
8.
Move to the center of the cab remove the tape that is covering the center running board holes and insert (1) M12 bolt/ M10 nut plate
into it as stated in step 3 (FIGURE 4) , attach the center mounting bracket to the bolt/nut plate using (1) M12 flat washer, (1) M12
lock washer, (1) M12 hex nut, (1) M10 hex head bolt, (1) M10 lock washer, and (1) M10 flat washer. Do not fully tighten at this time
9.
Move to the rear of the cab and remove the tape covering the rocker panel holes. Attach the rear mounting bracket as stated in step 8.
NOTE: On CREW CAB models the center and rear mounting bracket will be installed with the step bar cradles facing the
rear of the vehicle, ON QUAD CAB models the center mounting bracket is installed with the cradle facing the rear of the vehi-
cle, and the rear mounting bracket is installed with the cradle facing the front of the vehicle.
10. Take the passenger side step bar and attach to the front support and front mounting bracket using (1) 1/2" hex head bolt, (1) 1/2" lock
washer and (1) 1/2" flat washer (FIGURE 3) do not fully tighten at this time.
11. Attach the step bar to the center and rear mounting brackets, align the slots in the mounting brackets with the step bar riv nuts.
NOTE: On CREW CAB models the rear bracket will attach to the last set of riv nuts, ON QUAD CAB models the second to
the last set of riv nuts are used. Attach using (4) M10 button head screws (4) M10 toothed lock washers, and (4) M10 flat washers.
Use the extra M10 button head screws and install the in the unused riv nuts to prevent corrosion. Do not fully tighten at this time.
12. Repeat steps 2-11 for drivers side
13. Adjust and align step bar and tighten all hardware at this time, torque all M12 hardware to 40-45 ft lbs all M10 hardware to 30-35 ft
lbs, and 1/2" hardware to 50-55 ft lbs.
DESCRIPTION
BARRES MARCHEPIED
SUPPORTS DE MONTAGE AVANT (2) COTE CONDUCTEUR, (3)
COTE PASSAGER
SUPPORTS DE FIXATION AVANT
SUPPORTS DE MONTAGE CENTRAL
SUPPORTS DE MONTAGE ARRIERE
PLAQUES A M12 BOULON/M10 ECROU
M12 PLAQUES A BOULON
M12 RONDELLES PLATES
M12 RONDELLES-FREIN
M12 ECROUS HEXAGONAUX
M10 X 35MM BOULONS HEXAGONAUX
M10 RONDELLES PLATES
M10 RONDELLES-FREIN
1/2" X 2" BOULONS A TETE HEXAGONALE
1/2" RONDELLES PLATES
1/2" RONDELLES-FREIN
M10 X 25MM VIS A TETE BOUTON (ZINC NOIR)
M10 RONDELLES PLATES (ZINC NOIR)
M10 RONDELLE-FREIN DENTEE (ZINC NOIR)
11MM BUTOIRS PLASTIQUES
2
OUTILS NECESSAIRES
17MM DOUILLE
15MM DOUILLE
CLE DYNAMOMETRIQUE
OUTIL ALLEN (INCLUS)
75-1035 REV A 9/19/10
17MM CLE
15MM CLE
3/4 DOUILLE
CLIQUET
Publicidad
