Kichler VLO 3000K Guia De Inicio Rapido

SAFETY INSTRUCTIONS
KEEP THESE INSTRUCTIONS
CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main fusebox before starting and during the installation.
WARNING:
If fixture is installed less than 1.5m (5 ft) from the inside walls of the pool it must be supplied by
a listed transformer or power supply that complies with NEC article 680.23 (A) (2).
WARNING:
This fixture is intended for installation in accordance with the National Electric Code (NEC) and Local code
specifications. Failure to adhere to these codes and instructions may result in serious injury and/or property
damage and will void the warranty.
1) WARNING: This fixture is not to be installed within 10 feet (3M) of a pool, spa or fountain.
2) According to the requirements of the National Electric Code (NEC), direct burial rated wire is to be buried a
minimum of 6" [152mm] beneath the surface of the ground.
NOTE: If additional Direct Burial wire is needed, contact your local Kichler
• 8 GA wire can be purchased in length of 250' (76 M),15503-BK.
• 10 GA wire can be purchased in length of 250' (76 M),15504-BK.
• 12 GA wire can be purchased in lengths of 100' (30 M),15501-BK; 250' (76 M), 15502-BK; 500' (152M),
15505-BK; and 1000' (304 M), 15506-BK.
3) Wiring connections must be made with approved/listed wire connection device(s) suitable for the application. Do
not exceed manufacturers' wiring combination specifications for size and quantity of conductors.
WHEN INSTALLING KICHLER LANDSCAPE LIGHTING (LINE VOLTAGE OR LOW VOLTAGE), CARE SHOULD BE TAKEN TO
KEEP CLEAR OF POTENTIALLY COMBUSTIBLE MATERIALS. WHEN MAINTAINING THE FIXTURES, BE SURE TO REMOVE
LEAVES, PINE NEEDLES, GRASS CLIPPINGS, MULCH, OR ANY DEBRIS THAT HAS ACCUMULATED ON THE LIGHT BULB,
LENS, OR BODY OF THE FIXTURE.
ASSEMBLY AND INSTALLATION
1) Determine desired location for mounting fixture.
2) At desired location, hammer stake into ground. To avoid damage to stake, place a board on top of
stake while hammering. If ground is hard and stake is difficult to install, make a crosscut in ground
using a flat shovel.
3) Clear away area in ground at wireway slot in top of stake.
4) Lay 12V cable into wireway slot and screw fixture into stake. Aim fixture in desired direction and
secure by tightening locknut. If necessary, use wrench or pliers for final tightening of nut.
5) Adjust angle of accent light by loosening Phillips head screw.
6) Adjust angle of cowl by loosening thumb screw.
7) TURN OFF POWER.
8) Make wire connections using supplied wire connectors following instructions included, or using
other approved wiring connection method (not supplied).
TO CHANGE LIGHT OUTPUT SETTING:
• NOTE: Fixure switches up in terms of lumen settings; it starts at medium (200 lumens) for the small
accent and starts at low (400 lumens) for the large accent. If these levels are desired, no adjust-
ment is needed.
• Locate the dimple at the top of the fixture. (This is called a lumen adjustment switch locator)
• Hold magnet on lumen adjustment switch locator for 1.5 seconds to begin programming mode.
Remove magnet.
• Fixture will blink continuously 4x's at full brightness level and go dark for 2 seconds and then will
illuminate at original factory setting.
• To switch lumen settings, magnet must be reapplied to lumen adjustment switch locator for 1.5
seconds and magnet must be removed for 1 second between switching.
• NOTE: fixture blinks 1x for the lowest lumen setting; 2x's for the middle lumen setting, and 3x's for
the highest lumen setting.
• Once the fixture is set and magnet removed, it stays in programming mode for 2 minutes.
• After 2 minutes, the memory is set.
• To change the output brightness, return to programming mode by holding magnet on magnetic
locator for 1.5 seconds.
• NOTE: Fixture reverts back to original factory setting when put back into programming mode.
Wire G auge/Power/Length C hart
Wire G auge/Length ( ft/m) p er r un
WATTS ( VA) 10
0 -­‐ 2 0 1860/567
40 930/283
60 620/189
80 470/143
100 370/113
C onsult T echnical S upport >100
Fixture L oad C hart
Fixture Lumen
AC V oltage ( VA)
Style Level 9V
Large 17
3
Large
2 12
Large 1 8
Small 3 7.5
Small 2 5.5
Small 1 3.5
NOTE: When sizing your transformer please use the highest VA you
expect to use depending on desired lumen level to prevent potentially
overloading the transformer.
REV: 02-MAR-2021
READ THIS FIRST
landscape distributor.
®
CAUTION
12 14 16
1150/351 730/223 450/137
580/177 370/113 230/70
390/119 240/73 150/46
290/88 180/55 110/34
230/70 140/43 90/27
DC V oltage ( W)
12V 15V 9V 12V
17.5 18 12
12.5
9
13 8
13
9 9 6 5.5
7.5 8 5.5 5.5
5.5 5.5 3.5 3.5
3.5 3.5 2 2
For warranty information please visit: kichler.com/warranty
LUMEN ADJUSTMENT
SWITCH LOCATOR
Small A ccent
16015-­‐ 1 6017
Large A ccent
16018-­‐ 1 6020
LUMEN ADJUSTMENT
SWITCH LOCATOR
SWITCHING
MAGNET
15V
12
8
5.5
5.5
3.5
2
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1) This device may not cause harmful interference, and
2) This device must accept any interference received, including interference that may
cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
We're here to help
FIXTURE
PHILLIPS HEAD SCREW TO
ADJUST ANGLE OF FIXTURE
LOCKNUT
STAKE
Gen 3 L umen T able f or I S -­‐ 0 5112017.xlsx
PROGRAMMING MODE
Lumen L evel T able ( For 2 700K/3000K)
Level 1 Level 2 Level 3
100 L m *200 L m 300 L m
*400 L m 600 L m 835 L m
* DENOTES FACTORY SETTING
FCC INFORMATION
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
866-558-5706
Hrs: M-F 9am to 5pm EST
THUMB SCREW TO AD-
JUST ANGLE OF COWL
OR TO LOOSEN AND
REMOVE COWL
WIRE LEADS
SWITCHING
MAGNET
ORIGINAL
PROGRAMMING MODE
LEVEL 1
LEVEL 2
LEVEL 3
Confidential
IS-16015-US