Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
The charging indicator (12) will be lit as long as the battery is
connected to the plugged-in charger.
Charge discharged batteries within 1 week. Battery life will
be greatly diminished if stored in a discharged state.
Charging indicators
If the charger detects a problem with the battery, the charging
indicator (12) will flash at a fast rate. Proceed as follows:
Re-insert the battery (10).
If the charging indicators continues flashing at a fast rate,
use a different battery to determine if the charging process
works properly.
If the replaced battery charges correctly, the original
battery is defective and should be returned to a service
centre for recycling.
If the new battery gives the same indication as the original
battery, take the charger to be tested at an authorised
services centre.
Note: It may take as long as 15 minutes to determine that the
battery is defective. If the battery is too hot or too cold, the
LED will alternately blink fast and slow, one flash at each
speed and repeat.
Adjusting the position of the secondary handle
(fig. F)
The secondary handle (4) can be adjusted to provide optimum
balance and comfort.
Let the shroud (9) rest on the ground.
Slacken the handle knob (5).
Move the handle into the desired position.
Securely tighten the handle knob.
Adjusting the height (fig. G)
The telescopic shaft (19) allows you to set the tool to a
comfortable height.
Loosen the collar (6).
To increase the height, slide the shaft out.
To reduce the height, slide the shaft in.
Tighten the collar.
Switching on and off (fig. H)
For your safety, this tool is equipped with a double switching
system. This system prevents starting the tool inadvertently.
Switching on
Push the lock-off button (2) backward using your thumb
and at the same time squeeze the on/off switch (1).
Release the lock-off button.
Switching off
Release the on/off switch (1).
Warning! Never attempt to lock a switch in the on position.
Hints for optimum use
Hold the tool as shown in fig. I.
If the tool starts running slowly, reduce the load.
For the first cultivating each season, move slowly because
dirt is packed down. Subsequent cultivating will be
completed more rapidly.
In order to achieve optimum results, only cultivate dry soil.
If the tines become clogged, immediately switch off the
tool. Refer to the maintenance instructions to unclog the
tines. To continue operating the tool in a clogged condition
will damage the tool.
If possible, keep the battery connected to the charger and
the charger plugged in whenever the tool is not in use.
Maintenance
Your Black & Decker tool has been designed to operate over a
long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
Warning! Before performing any maintenance on the tool,
remove the battery from the tool. Unplug the charger before
cleaning it.
Regularly clean the ventilation slots in your tool and
charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
Regularly use a blunt scraper to remove grass and dirt
from the underneath of the shroud .
Make sure all switches are free of debris before and after
use.
Warning! Do not immerse tool in water or spray it with a hose.
During use
Remove clogged material from the tines with a stick or
scraper.
Warning! Do not attempt to unclog the tines by dropping or
tapping the tool on the ground. Wear gloves when cleaning
tines.
After use and before storage
After use, carefully clean the tines. After cleaning, apply a
film of light machine oil to prevent the tines from rusting.
Note: Fertilizers and other garden chemicals contain agents
that greatly accelerate the corrosion of metals. If you use the
tool in areas where fertilizers or chemicals have been used,
the tool should be cleaned immediately afterwards.
ENGLISH
7
Publicidad
Tabla de contenido
