JTS HPM-535 Manual De Instrucciones página 2

www.jts-germany.de
These instructions are intended for
ENGLISH
users without any specific technical
knowledge. Please read the instruc-
tions carefully prior to operation and
keep them for later reference.
1 Applications
These headphones offering excellent sound
quality have been designed both for pro-
fessional communication and for gaming at
home. The headband and the ear cups are
padded and very comfortable to wear.
2 Important Notes
The headphones correspond to all relevant
directives of the ( mark).
CAUTION Never adjust the headphones
to a very high volume. Perma-
nent high volumes may dam-
age your hearing! Your ear will
get accustomed to high volumes which do
not seem to be that high after some time.
Therefore, do not further increase a high vol-
ume after getting used to it.
•
The headphones are suitable for indoor
use only. Protect them against dripping
water, splash water and high air humidity.
The admissible ambient temperature range
is 0 – 40 °C.
•
Keep the headphones away from any
items sensitive to magnets (credit cards,
audio tapes etc.); the headphone magnets
are strong and may damage these items.
•
For cleaning only use a dry, soft cloth; never
use water or chemicals. For cleaning the
ear cushions, however, a damp cloth and a
mild detergent may be used.
•
No guarantee claims for the headphones
and no liability for any resulting personal
damage or material damage will be ac-
cepted if the headphones are used for
other purposes than originally intended,
if they are not correctly connected, if they
are overloaded or not repaired in an expert
way.
If the headphones are to be put out
of operation definitively, take them to
a local recycling plant for a disposal
which is not harmful to the environ-
ment.
Vertrieb von JTS-Produkten – Distribution of JTS products
3 Operation
1) Place the foam pop shield onto the
microphone.
2) Connect the plug of the headphones with
the symbol
the headphone output or audio output of
your audio unit /computer.
Audio Out
(Phones)
green
3) Connect the microphone plug with the
symbol and the red isolators to the micro-
phone input of your audio unit /computer.
Mic In
red
Note: At the microphone input of the audio unit,
a supply voltage for the microphone of the head-
phones must be available (refer to specifications).
If not, use a power supply adapter (e. g. model
EMA-20 from MONACOR INTERNATIONAL). With-
out this supply voltage, the microphone will not
be able to transmit a signal. (Computer sound
cards will always supply this voltage.)
4) Put on the headphones and adjust the
length of the headband to ensure a com-
fortable fit.
5) Put the microphone arm in a position where
the microphone is close to your mouth.
®
MONACOR INTERNATIONAL GmbH & Co. KG, Zum Falsch 36, 28307 Bremen, Germany
Copyright by MONACOR INTERNATIONAL. All rights reserved. A-1762.99.01.04.2016
©
and the green isolators to
L
3
1
HPM-535
Order No. 22.0210
Professional Stereo Headphones
with Boom Microphone
4 Specifications
Headphones
Driver: . . . . . . . . . . . . . . dynamic,
neodymium magnet
Diaphragm: . . . . . . . . . . ⌀ 40 mm
System: . . . . . . . . . . . . . semi-open
Transmission range: . . . 20 – 20 000 Hz
Power rating: . . . . . . . . . 1 W
SPL: . . . . . . . . . . . . . . . . 104 dB (1 mW, 1 kHz)
Nominal impedance: . . 64 Ω
Cable length: . . . . . . . . . 2 m
Plug: . . . . . . . . . . . . . . . 3.5 mm plug, gold-plated
Weight: . . . . . . . . . . . . . 308 g without cable
Microphone
Microphone type: . . . . . electret
Polar pattern: . . . . . . . . cardioid
Transmission range: . . . 100 – 15 000 Hz
Impedance: . . . . . . . . . . 680 Ω
Sensitivity: . . . . . . . . . . 6.3 mV/Pa at 1 kHz
DC power supply: . . . . . 1.5 – 10 V
Plug: . . . . . . . . . . . . . . . 3.5 mm plug, gold-plated
Subject to technical modification.