Descargar Imprimir esta página

Publicidad

Enlaces rápidos

Shure cartridges can be used in DJ or Hi-Fi applications.
Note: the M70BX is not recommended for heavy scratching.
1.
Carefully remove the stylus from the cartridge. See
Figure 1.
2.
Use needle-nose pliers to connect the colored wires
from the tonearm headshell to the corresponding
pins on the cartridge. See Table 1 and Figure 2.
HEADSHELL WIRE
RIGHT "HOT"
RIGHT GROUND
LEFT "HOT"
LEFT GROUND
Table 1. Cartridge Wiring
1.
Attach the cartridge to the headshell using the screws
supplied. See Figure 3. Tighten the screws after
positioning the cartridge (and headshell weight, if
desired) according to one of the methods described
below.
2.
Carefully insert the stylus into the cartridge.
Hi-Fi Setup: For maximum fidelity and minimal record wear, position the cartridge using an alignment
protractor or the overhang gauge supplied with your turntable. Level your tonearm (See Figure 7). Use
Table 2 and "Setting a Precise Tracking Force", below, to set the typical tracking force for your cartridge.
Set the anti-skate control to the same number as the tracking force.
Standard DJ Setup: Mount cartridge at rear of headshell. Set tonearm height to 4-5. Set tracking force
to 3 grams. Set anti-skate control to 0.
Unorthodox DJ Setup: Reverse the counterweight and mount it flush with the end of the tonearm.
Mount cartridge (with headshell weight) flush with the front edge of the headshell. Set anti-skate
control to 0.
Level Your Tonearm
Figure 7
©2005, Shure Incorporated
27C3116 (Rev. 3)
Install Your Cartridge
COLOR
PIN
RED
R
GREEN
RG
WHITE
L
BLUE
LG
Choose a Method for Cartridge Positioning
25, 35, and 44 Series
Phono Cartridges
Figure 2
Figure 4
4 - 5
Figure 5
4 - 5
Figure 6
Extra Skip Resistance for DJ's:
Mount the cartridge at a 23 degree angle as
shown, so that the cartridge points to the
tonearm pivot. Set anti-skate to 0.
23
O
Figure 1
Figure 3
3 grams
0
Printed in U.S.A.
0

Publicidad

loading

Resumen de contenidos para Shure 25 Serie

  • Página 1 25, 35, and 44 Series Phono Cartridges Shure cartridges can be used in DJ or Hi-Fi applications. Note: the M70BX is not recommended for heavy scratching. Install Your Cartridge Carefully remove the stylus from the cartridge. See Figure 1. Use needle-nose pliers to connect the colored wires from the tonearm headshell to the corresponding pins on the cartridge.
  • Página 2 Inductance M44: 720 mH,M35, from date of purchase. You should retain proof of date SC35C: 425 mH of purchase. Shure is not liable for any consequential M70BX: 600 mH damages. If this Shure product has any defects as Channel Separation...
  • Página 3 Régler l’antiskating à 0. Shure n’est pas responsable pour les dommages-intérêts indirects. Si ce produit Shure présente un des défauts Mise à niveau du bras de lecture : Voir figure 7. décrits plus haut, le remballer soigneusement et le retourner en port payé...
  • Página 4 United States, Canada, Latin America, Caribbean: 5800 W. Touhy Avenue, Niles, IL 60714-4608, U.S.A. Phone: 847-600-2000 U.S. Fax: 847-600-1212 Int’l Fax: 847-600-6446 Europe, Middle East, Africa: Shure Europe GmbH, Phone: 49-7131-72140 Fax: 49-7131-721414 Asia, Pacific: Shure Asia Limited, Phone: 852-2893-4290 Fax: 852-2893-4055...

Este manual también es adecuado para:

35 serie44 serieM44-7M44gM35s35x ... Mostrar todo