Publicidad
Idiomas disponibles
Idiomas disponibles
PSS-1500SV
Order number 27.3450
ELECTRONICS FOR SPECIALISTS
Switch Mode Power Supply Unit
GB
Please read these operating instructions carefully prior to
operating the unit and keep them for later reference.
1 Applications
This power supply unit is used for direct current supply of
small units with an operating voltage between 9 V and 24 V
and a maximum current consumption of:
1.5 A at 9 – 15 V
1.2 A at 18 – 20 V
1.0 A at 24 V
The output voltage is adjustable to 9 V, 12 V, 13.5 V, 15 V,
18 V, 20 V or 24 V. The unit is protected against short circuit,
overload and overheating. The special feature of the power
supply unit is its extra low current consumption (< 0.3 W) when
the unit connected has been switched off.
2 Safety Notes
This unit corresponds to all relevant directives of the EU and
is therefore marked with
WARNING
The unit uses dangerous mains voltage.
Leave servicing to skilled personnel only. Inex-
pert handling unit may result in electric shock.
G
The unit is suitable for indoor use only. Protect it against
dripping water and splash water, high air humidity and heat
(admissible ambient temperature range 0 – 40 °C).
G
Do not operate the unit or immediately disconnect the plug
from the mains socket
1. if the unit is visibly damaged,
2. if a defect might have occurred after the unit was
dropped or suffered a similar accident,
3. if malfunctions occur.
In any case the unit must be repaired by skilled personnel.
G
For cleaning only use a dry, soft cloth; never use chemicals
or water.
G
No guarantee claims for the unit and no liability for any
resulting personal damage or material damage will be
accepted if the unit is used for other purposes than origi-
nally intended, if it is not correctly connected, if it is over-
loaded or if it is not repaired in an expert way.
If the unit is to be put out of operation definitively,
take it to a local recycling plant for a disposal which
is not harmful to the environment.
Œ
Positive pole at the tip or at the
inner contact
ELECTRONICS FOR SPECIALISTS
.
Negative pole at the tip or at
the inner contact
®
MONACOR INTERNATIONAL GmbH & Co. KG
Copyright
©
by MONACOR INTERNATIONAL. All rights reserved.
ELECTRONICS FOR SPECIALISTS
3 Operation
1) Determine the operating voltage of the unit to be supplied
with power (
unit) and adjust the voltage by turning the switch (3) with
the key supplied (2).
2) Select the matching adapter from the 7 adapters supplied:
Type
Plug
Hollow
plug
3) Determine the position of the positive and negative poles
at the power supply jack of the unit to be connected
(
marking of the jack) and connect the adapter to the
inline jack (1) accordingly.
With this marking or a similar marking of the power
supply jack, the positive pole must be at the tip or at
the inner contact of the adapter: Connect the
adapter to the inline jack in such a way that the
arrow of the inline jack will point to the number/
numbers of the adapter (fig. 1).
With this marking, the negative pole must be at the
tip or at the inner contact of the adapter: Connect
the adapter to the inline jack in such a way that the
arrow of the inline jack will point to the identification
letter (fig. 2).
4) Use the correct adapter to connect the power supply unit to
the unit to be supplied with power; then connect it to a
mains socket (100 – 240 V~, 50 – 60 Hz). The red power
LED will light up.
4 Specifications
Power supply: . . . . . . 100 – 240 V~, 50 – 60 Hz, 500 mA max.
Power consumption
in no-load operation: . < 0.3 W
Output voltage: . . . . . 9/12 /13.5 /15 /18 / 20 / 24 V
Output current
9 – 15 V: . . . . . . . 1.5 A
18 – 20 V: . . . . . . . 1.2 A
24 V: . . . . . . . . . . . 1.0 A
Dimensions: . . . . . . . 52 × 59 × 95 mm
Weight: . . . . . . . . . . . 190 g
Subject to
technical modification.
•
Zum Falsch 36
ELECTRONICS FOR SPECIALISTS
marking of the power supply jack of the
Diameter (mm)
2.5
3.5
outside
inside
2.35
0.75
3.5
1.35
5.0
2.1
5.5
2.1
5.5
2.5
•
28307 Bremen
A-1576.99.01.07.2014
Identification letter
A
B
S
H
D
E
G
Ž
•
Germany
Publicidad
