Troubleshooting - LUTEC 9054 Instalación

Explanation
EN.
A
. The GreenBall to sensor range is maximum 30m.
B
. Spike or Screw installation
C
. Please charge 30 minutes under the sunlight for the solar panel before use
D
. Connections:The Solar panel and/or 12V DC adapter
E
. Connect to light fixtures.
F
. Note the "+","-" polarity! Connect the interface correctly, and then screw the waterproof cap tightly.
G
. Test in daylight: Turn on the solar panel switch , cover with a cloth (not provided), and/or plug 12V DC adapter, the
fixtures will flashs twice, means all the cables connected correctly. (Note: Remove the cloth for normal use)
H
. Sensor Synchronisation: press switch for about 3 seconds then loose, the red & blue LEDs will flash.
I
. Sensor Set-up: Adjust the TIME Setting to TEST mode, then install the batteries.
J
. The Sensor's LED will lights up about 15 seconds when the batteries are installed correctly.
K
. The red & blue LEDs (of the Greenball) will light up about 10s, then off when synchronisation is made. The Greenball is
now in motion sense mode. If not, remove and reinstall the sensor's batteries.
L
. Two Installation ways.
M
. Adjust the sensor according to your preferences and enjoy the SUN-CONNEC system!
N
. NOTES: 1.SUN-CONNEC system only work at night except when in TEST mode;
2. Once synchronized, you can press the switch to choose Dusk-Dawn mode or motion sensor
mode according to your preferences without do any other synchronization.
SENSOR SETTING
TIME Setting
TEST
1/3/10Min

TROUBLESHOOTING

PROBLEM
The greenball and sensor can not
connect to each other
The fixture will not illuminate.
The fixture stays on continuously.
The fixture flashes
Motion is not detected within the
coverage area.
DISTANCE Setting
Set the DISTANCE to the S, M, L.
L is the maximum detection distance- 12m at the
angle of 78º.
DISTANCE SETTING:
S: Up to 5 Meters.
M: Up to 8 Meters.
L: Up to 12 Meters.
POSSIBLE CAUSE
1. There is more than 30 meters between these two
units.
2. There are obstructions in between the two units.
3. The sensor install in corner or etc.
4. The sensor fail to synchronise with greenball.
1. The cable plug isn't properly connected.
2. The batteries in sensor are low or drained.
3. The batteries in sensor are not properly
connected.
4. The sensor may be detecting daylight or other
bright light source near the unit at dusk.
1. There are other movements that trigger the
sensor.
1. The photocell is detecting light from the LED
lamps and interpreting the LED light as daylight and
in response is trying to turn off the lights.
1. The motion is directly towards the sensor.
2. The sensor maybe too close to an air conditioner
or hot air flow.
3. There is dust on the motion sensor lens.
4. The greenball is in DUSK-DAWN mode
Description
When the sensor detects movement, the light
will turn on for about 15 Sec.
(Can be tested without Greenball)
At dusk, the motion sensor becomes active. Any
movement within the coverage will cause the
light to turn on. After movement has stopped,
the light will remain on for the setting time of 1
or 3 or 10 minutes.
At dawn, the motion sensor will deactivate.
CORRECTIVE ACTION
1. Make sure they are less than 30 meters apart.
2. Make sure there are no obstructions.
3. Make sure the sensor not installed in such
narrow space.
4. Synchronize again according to the steps.
1. Make sure the cable plug is connected well.
2. To replace new AAA R03 batteries. ( This kind
battery is not rechargeable)
3. Make sure the batteries are connected well.
4.Try to avoid such lighting source.
1. Avoid other movements that may trigger the
sensor needlessly.
1. Try to reposition the lamps so that reflected
back to the detector is minimized.
1. The sensor is more sensitive to motion that
across the detection field.
2. Avoid installing the sensor near such place.
3. Clean the dust on the lens.
4. Press switch to active the motion sensor mode.