Lista CCE1500 Traducción De Instrucciones Originales página 33

ASSEMBLY
Intended Use
This product is intended for domestic lawn
mowing.
ASSEMBLY
The lawn mower is supplied dismantled. The
complete handle, the grass catcher must all be
assembled before the lawn mower can be used.
In order to assemble the lawn mower without
difficulty, follow the operating instructions step by
step, with reference to the pictures as you do so.
IMPORTANT! Before you assemble the
lawn mower, check the accessories and
make sure they are complete.
1. FITTING THE WHEELS (See Fig A1 A2 A3
A4 A5)
The wheels for your lawn mower will not be
installed.
Notice that there two large wheel assemblies and
two smaller wheel assemblies.
The large wheels fit on the rear and the small
wheels are for the front of the lawn mower.
To install the wheels:
1) To insert the wheels to the side of the motor
desk. (See Fig A1)
2) Be careful the hole on the shaft must appear
above the surface of the wheel at least 8mm. if
not, please lift the shaft out from the surface of
the wheel. (See Fig A2)
3) To put the washer(a) on the wheel's centre
firstly, and insert the pin(b) to hole of the shaft.
(See Fig A3)
4) To use the tool to make the ends of pin to the
opposite directions. (See Fig A4)
5) To put the wheel cover(c) to the wheel with
aligning the holes on the wheel. (See Fig A5)
2. FITTING THE LOWER HANDLE (See Fig B1
B2 B3 B4 B5 B6 B7 B8 B9)
1) Remove the packaging from the lower handle.
2) Firstly insert the Cable Retaining Hook (11) to
the lower handle(2) before fitting the lower handle
to the mower deck. (See Fig B1 B2)
2) Remove the fixed disk (d) and the Securing
knob (5) from the mower deck (1) included in
carton box firstly. (See Fig B3) Then the fixed
disk and securing knob is ready for fitting. (See
Fig B4 B5)
3) Insert the fixed disk (d) to the lower handle (2),
and align the holes as shown.(See Fig B6)
4) Fit the lower handle (2) to the mower deck(1)
as shown.(See Fig B7) and align the holes.
5) Tighten the lower handle (2) to the mower
deck(1) with the Securing knob (5). The screws
must be fitted outside of the deck as shown
(See Fig B8), after tightening the Securing knob,
Please put the handle of the Securing knob
towards to the lower handle for locking closely as
shown (See Fig B9)
3. FITTING THE UPPER HANDLE (See Fig C1
C2 C3)
1). Lift the upper handle (3), Align the holes
between the upper handle (2) and lower handles
(3).
2) Insert the Securing knob (5) into the holes
and tighten them with the wing nuts (e1 e2 e3)
provided, making sure the cable is not twisted.
(Be careful that e1 e2 are on the left side of the
handles. And the Securing knob (5) is on the right
side of the handles).
3). Fasten the cable to the upper handle and the
lower handle with the cable clips (4). (See Fig
C3)
4. GRASS CATCHER – Assembling (see Fig
D1 D2 D3)
1) To assemble the two halves of grass catcher'
bottom firstly.
2) To snap together the top to the bottom of grass
catcher halves by pushing all the "snap fits"
together around the edges; start from the rear
and work towards the front.
3)Assemble the handle to the top of the catcher.
5. INSTALLING/REMOVING THE GRASS
CATCHER (See Fig. E1 E2)
Note: always fit the grass catcher before
starting.
1) T o remove the grass catcher, raise the safety
flap(f) with one hand and remove the grass
catcher using its handle with your other hand.
2) To maintain safety, the safety flap(f) will close
back to cover the rear discharge opening, when
you release the flap.
3) Empty the grass debris in the glass catcher,
and refit glass catcher as above instruction.
4) If any grass residues are caught in the
opening, clean it using a pushing bar.
5) Do not remove grass debris in the mower
casing or on the blade by hand or with your feet.
Instead use suitable tools such as a brush or
broom.
6) To ensure that the cutting grass can be blown
into glass catcher, the discharge opening and
inside the mower casing must be cleared of any
blockage.
Note: The motor must always be switched
off and the blade must have stopped rotating
33