Simu 9014736 Manual Del Usuario página 2

GB SOLAR PANEL - 9014736
S.A.S. au capital de 5 000 000 - Z.I. Les Giranaux - BP71 - 70103 Arc-Les-Gray CEDEX - RCS GRAY B 425 650 090 - SIRET 425 650 090 00011 - n° T.V.A CEE FR 87 425 650 090
Presentation
1
Protective foam
- Ensure that the cables are not damaged during installation. Smooth the edges of all
the drilled holes.
- Do not put anything on the solar panel that would filter the sun's ray (e.g.: paint...).
- The photovoltaic cells must be kept clean (wash over with clean water).
- In winter, do not allow snow to build up on the panels.
Installation
2
2.1 - Fastening the solar Panel(s) by riveting
2.1a - Holes in the box and console (WARNING: do not drill either the panel or its frame)
Drilling measurements (mm) for panels placed to the left of the box:
70 360
15
20
Ø4,2
st
1 panel
Ø15
15
2.1b - Fixing the Panel(s)
OK
6mm
1
2.2 - Fastening the Panel(e) by gluing
2.2a - Holes in the box and console
Hole for Panel(s) located to the left of the box:
500
15
20
st
1 panel
Ø15
15
2.2b - Preparation of the box and gluing of the Panel(s)
OK
1
3
2
(ref.: 9014734) in the Autosun system.
Technial data:
- Current supplied by 1 panel (Isc ): 78,6 mA
- Voltage supplied by 1 panel (Uoc ): 24,5 V
Wiring for two panels*
(ref.:5050240A) - Umpp = 18V - Impp = 61,2 mA
- For some applications, two solar panels may be required. See Simu data sheet ref: 5055194.
- To use 2 panels, the installation must have the panels positioned on the left.
570
360
Ø4,2 Ø4,2
nd
2 panel*
2
2
3
1000
nd
55
2 panel*
4
3
4
5
By converting solar energy to electrical energy, the solar panel charges the battery pack
- We recommend users run industrial tests in exactly the same conditions as
those of the intended application and thereby ascertain that our product
satisfies its requirements. If in doubt, opt for the riveting solution.
Drilling measurements (mm) for panel placed to the right of the box:
Ø4,2
14
*
1- Pass the wires of the Panel(s) inside the box (Ø15 hole) with the
3
2- Fix the Panel(s) using aluminium Ø4 pop rivets in the Ø4.2 holes
3- Remove the protective film(s).
Hole for panel located to the right of the box:
Recommendations:
- Use a solvent containing a mixture of isopopyl alcohol and water (50/50) or a
heptane-based solvent.
*
- Follow all the safety instructions concerning the handling of solvents.
- The ambient temperature when gluing should be between 20°C and 38°C.
5
- The surfaces to be glued must be dry and clean.
1- Clean the surfaces to be glued with solvent and wipe.
2- Pass the wires of the Panel(s) inside the box (Ø15 hole) with the protective
foam.
3- Remove the protective paper from the adhesive.
4- Fix the Panel(s) to the box applying a uniform amount of pressure.
WARNING : Apply the pressure to the panel frame and not to the photovoltaic cells.
5- Remove the protective film(s).
360
Ø4,2 Ø4,2
14
protective foam.
drilled during operation 2.1a.
* Mounting with two panels only.
500
55
5055193A
Read carefully these
instructions before any use.
70
20
15
Ø15
15
20
15
Ø15
15
1 / 1