Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
PROGRAMMING
When the expander is installed, program device as described following:
1) Carry out coding of the Device by means of the first 5 microswitches on the Dip-switch
[9], as shown in Tab. 1 (32 available addresses).
Input/Output Expanders programmed to function as Output Expanders can
be assigned ONLY the first 16 addresses.
2) Set the operating mode using microswitches 6 and 7 on Dip-switch [9] as shown
in the following table:
Microswitches no. 6 and 7
no. 6 no. 7
OFF OFF
Input Expander with 4 Inputs + Output Expander with 2 Outputs
ON OFF
(T1 and T2 Outputs; T3, T4, T5 and T6 Inputs)
Output Expander with 4 Outputs + Input Expander with 2 Inputs
OFF ON
(T1, T2, T3 and T4 Outputs; T5 and T6 Inputs)
ON
ON
Output Expander with 6 Outputs
If the M-IN/OUT Expander is programmed as an Input and Output Expander,
it must be configured as an Input Expander and as an Output Expander. For
example, if you have programmed an M-IN/OUT Expander as an Input
Expander and Output Expander, and assigned it address no. 1, you must
configure Input Expander no. 1 and Output Expander no. 1.
Zones relating to M-IN/OUT expanders programmed as Input and Output
Expanders are NOT all usable, even if they are shown on the application/
display. For example, if an M-IN/OUT Expander is configured as an Expander
with 4 Zones + Expander with 2 Outputs, only the Zones corresponding to
terminals L3, L4, L5 and L6 will be usable; if it is configured as an Expander
with 4 Outputs + Expander with 2 Zones, only the Zones corresponding to
terminals L5 and L6 will be usable.
Outputs relating to M-IN/OUT expanders programmed as Input and Output
Expanders are NOT all usable, even if they are shown on the application/
display. For example, if an M-IN/OUT Expander is configured as an Expander
with 4 Zones + Expander with 2 Outputs, only the Outputs corresponding
to terminals OC1 and OC2 will be usable; if it is configured as an Expander
with 4 Outputs + Expander with 2 Zones, only the Outputs corresponding
to terminals OC1, OC2, OC3 and OC4 will be usable.
BENTEL SECURITY recommends that customers dispose of their used equipments (panels, detectors, sirens, and other devices)
Potential methods include reuse of parts or whole products and recycling of products, components, and/or materials.
In the European Union, this label indicates that this product should NOT be disposed of with household waste.
BENTEL SECURITY srl reserves the right to modify the technical specifications of this product without prior notice.
Description
Input Expander with 6 Inputs
For specific information see: www.bentelsecurity.com/index.php?o=environmental
Waste Electrical and Electronic Equipment (WEEE) Directive
It should be deposited at an appropriate facility to enable recovery and recycling.
www.bentelsecurity.com/index.php?o=environmental
3) Set the operating mode of the Inputs using microswitch 8 on Dip-switch [9] as
shown in the following table:
O
F F
h T
i e
O
N
i l B
e S
If you enable the "Roller blind" zones on the M-IN/OUT Expander, by means
the Dip-swtich n. 8, DON'T enable the pulse counter on the Panel's console
software, if it is possible, to avoid redundant zone's analysis; It is better to
program the zone's sensitivity as standard (1 pulse) by means the Panel's
Console Software. In this way, the M-IN/OUT expander will able to both signal
the "Roller Blind" alarm and the cut wire tamper.
4) Set the operating mode for the tamper switch [10] and wall tamper switch [7]
using jumper [8]: L = Switches enabled; K = Switches disabled.
CONNECTING
The M-IN/OUT is connected to the 4-wire bus (on the Control panel), through which
it communicates with the Control panel itself and receives a feed for its own operation
(Expander can work only with 12 Volt BPI level).
For the connections refer to INTALLATION MANUAL of the Control Panel.
Refer to the Fig. 2 to connect the Roller Blind: the M-IN/OUT Expander's Input
(Zones) set as Roller Blind interface, can be programmed ad Normally Closed,
Balanced 10K , Double Balanced (10K+10K).
The cable used to connect the Roller Blind to the M-IN/OUT Expander must NOT
exceeds 50 m in length.
Note. The cutting of the alarm line CAN NOT BE detected if you set more than
1 Pulse for the zone where the Roller Blind is connected.
Recycling information
in an environmentally sound manner.
For specific information see:
M
c i
o r
s
w
c t i
A
I l l
p n
s t u
o
e p
a r
e t
p n
t u
f s
n u
i t c
n o
n i
o N
m r
l a
m
o
e d
d n
, s
e . i
t .
e h
o z
e n
o g
s e
n i
o t
a
a l
s n
v i t i
y t i
o
i r
5 f
s
a h
p r
p
s l u
s e
a
e r
h
n
. o
8
n i
o N
m r
l a
M
o
e d
a
d n
s a
a
c
n o
a t
t c
n i
e t
a f r
e c
r o f
R
m r
o
t n
e h
a b
s i s
o
t f
e h
r p
g o
a r
m
m
d
t e
c e
e t
i d
t n
e h
s
a p
e c
o
2 f
i m
u n
l o
r e l
d e
e t
. s
Publicidad
Tabla de contenido
