Mounting Procedure; Cleaning And Maintenance - RAVAK EVS1/L - 75 Instrucciones De Montaje

ELEGANCE
The bath wall is 750 mm wide and 1500 mm high.
Left wall is marked EVS1/L
Right wall is marked EVS1/R
This product comes completely assembled in one package including bath wall, mounting profile and mounting kit.
ATTENTION! The mounting kit is enclosed in the carton.
This bath wall can be used for all types of metal and plastic rectangular tubs mounted to the wall. The length of
the bathtub must be a minimum of 800 mm long and on the wall there must be a clear area with a minimum width
of 685 mm (no taps or bath shelving).
For this product to function properly it should only be installed on strong walls.

MOUNTING PROCEDURE

1. Before mounting, remove the plastic moulding from the mounting
profile ( picture 1 ).
2. Sit the bath wall on the tub with the mounting profile against the wall,
and with the rounded corner of the glass at the top.
3. Adjust the position of the bath wall so that the glass is approximately in
the middle of the upper rim of the bathtub. Make sure that the bottom of
the supporting post completely sits on the bathtub (
4. Align the bath wall vertically according to the mounting profile. Mark the
oval openings of the mounting profile on the wall.
5. Remove the bath wall. In the center of the marked oval, drill a 10 mm
diameter hole and place a dowel in it (
WATCHOUTFORELECTRIC,GASANDWATERMAINSINTHEWALL!
6. Place sealing compound on the bottom of the post (for mounting to the tray).
7. Set the whole bath wall onto the bathtub and lightly tighten the
5x50 mm bolts ( picture 5 ).
8. Slide the drip sill onto the bottom side of the glass with the "flange"
inwards ( picture 6 ).
9. Use the slots and screws on the mounting profile to adjust the bath wall
so that:
- the bottom edge of the strip is level with the edge of the bathtub;
- in functioning position, when it is stopped by its own weight, it will follow
the level of the bathtub.
10. After all adjustments have been made, tighten all bolts and mounting
screws on the mounting profile.
11. Test the function of the door several times in the whole range of its
positions, and check the lifting mechanism. Adjust the drip sill so that in its

CLEANING AND MAINTENANCE

ATTENTION!
Only use a soft cloth and normal household detergent for cleaning the lacquered surfaces, glass and plastic panels. Avoid using abrasive pastes, solvents,
acetones, etc.
We reco mmend the line of RAVAK ANTICALC products:
qualities of the RAVAK ANTICALC coating;
acrylic bathtubs, washbasins and water taps;
manufacturer is not responsible for damage caused by misuse, improper installation and repair of the product. The manufacturer has the right to constant
innovation and changes of the product.
The guarantee of the product is 24 months, only if the installation has been done by an authorized firm holding a certificate for Ravak products. In
all other cases, the guarantee time limit will be determined in accordance with the appropriate legal terms.
For further information concerning assembly, installation, and use and maintenance, please contact your local dealer.
Single bath wall
(according to the supporting wall
on the left or right side)
picture 2 ).
picture 3 ).
RAVAK ANTICALC CONDITIONER
RAVAK CLEANER works to remove old and dried-on debris from glass surfaces, shower frames, enamel and
RAVAK DISINFECTANT
RAVAK a.s.,
Obecnická 285, 261 01 Pøíbram I
tel.: +420 318 427 111 fax: +420 318 427 269
e-mail: smith@ravak.cz, www.ravak.com
functioning position it will lightly touch the bathtub (
12. Drill holes of 2.6 mm in diameter in the support post according to the pre-
drilled holes in the mounting profile. Secure the post using 3.5x13 mm self-
tapping screws.
13. Place one side of the plastic moulding into the mounting profile and
push slightly along the whole length to "lock" it into place (
14. Put RAVAK PROFESSIONAL
seam to a height of 100 mm above the bathtub (
15. Put some silicon on the underside of the decorative cap and seat it on
the upper end of the plastic post (
16. All joints and seals should be filled with
sealing compound which ensures a perfect cohesion of the plastics used.
a preparation which perfectly renews and maintains all the
is a special preparation with notable anti-bacterial and anti-fungal effects. The
EVS 1 - 75
CONTENTS OF MOUNTING KIT
1. Decorative cap No. 1
2. Plastic drip sill R + L
3. Dowel 10 mm diameter
4. Bolts for dowel 5x50 mm
5. Washer 5 mm diameter
6. Self-tapping screws 3.5x13 mm
7. Drill bit 2.6 mm diameter
8. Mounting instructions
picture 6 ).
picture 7
sealing compound on the outer vertical
picture 8 ).
picture 9 ).
RAVAK PROFESSIONAL
1pcs
1pcs
4pcs
4pcs
4pcs
4pcs
1pcs
1pcs
).