Comsafe Gun EL Manual Del Usuario página 5

4--11 Bed GUN EL 9.2017_Layout 1 27.09.17 17:50 Seite 5
GB USA
Operating instructions for the
electronic-lock GUN
ATTENTION: Please read this operating instruction
carefully, before you operate the lock or you try to tailor
a new combination of numbers. We do not undertake
any liability for functional disorder because of faulty
switch over or use of violence or improper use and nei-
ther for damage nor for loss of property which could be
put down i.e. to the not proper closing of the safe.
GENERALLY
Any button-activity is confirmed by a signal tone
sounds each time a button is pressed. The maximum
distance between 2 activities may not be more then
20 seconds otherwise the former entering is deleted.
1. OPENING THE WEAPON CABINET FOR
THE FIRST TIME
For opening the safe for the first time proceed as
follows:
1.1 Remove the small central plate on the front panel.
1.2 Insert the key into the key-whole and turn it
into a counter-clockwise direction.
1.3 Insert 4 pieces batteries
1,5 Volt AA each case
(KeySystem was delivered
without batteries).
Detailed information page 25.
2. PROGRAMMING A CODE
Attention: for this safe 2 different codes can be pro-
grammed (Usercode and Mastercode). For your per-
sonal security please insert both codes after opening
the safe the first time.
Before you use your safe for the first time you have to
enter your personal code (reasons of safety). You aren't
allowed to take the delivered code over. Before you
carry out the simply programming please think about
your code firstly. Use no personal data which can be
thought by any persons.
Keep your code and the keys in safe place where
only you can find it. Don't let the keys in the safe.
a/ PROGRAMMING THE USER CODE
a.1 Open the safe.
a.2 Press the red button (inside of the door at the
hinges).
a.3 There are two signal-tones and the yellow
LED switches on. Now you have 20 seconds
to start programming.
a.4 Enter the combination you desired (at leased
ENGLISH
a.5 After confirmation of the combination by the
b/ PROGRAMMING THE MASTER CODE
b.1 Open the safe.
b.2 Press two [2] times „ 0 " („ 00 ").
b.3 Press the red button inside the safe (at the back of
b.4 Type in the code (for security reasons at least
b.5 You will hear two [2] signal sounds after correct
b.6 Your master code has been successfully changed.
3. OPENING THE ELECTRONICAL-LOCK
3.1 Enter your own code and confirm your entry by
3.2 The green LED flashes and now you have
3.3 Turn the handle to the right side to open the safe.
4. CLOSING OF SAFE
4.1 Turn the handle to the left for closing the safe.
5. LOCKING DEVICE TIME BY ENTERING
If you enter the wrong code there are 3 signal-tones
and the yellow LED flashes. Now you have two more
attempts to enter the correct code. If you enter the
code 3 times wrong the lock blocks for 20 seconds.
During the locking-device-time the lock doesn't react to
any entry.
6. MECHANICAL EMERGENCY-OPENING
If you have forgotten your code or the battery is empty
please do that:
6.1 Remove the cover between the handle and
6.2 Put in the emergency-key and turn to the left
6.3 Now you can open the safe as usual
7. CHANGING THE BATTERIES
7.1 Open the battery opening on the back of the door.
7.2 Put in 4 pieces batteries 1,5 Volt AA.
Attention: Your new Weapon cabinet GUN and
it's content aren't automatically insured.
Please write a letter to your insurance about
the insurance value you'd like.
3 numbers, at most 8 numbers) and confirm
your entry by pressing the button "B".
button "B" there are two signal-tones and the
yellow LED goes off and shows, that the pro
gramming was successful.
the door, near the hinges).
3 numbers but maximum 8 numbers) that you
want. Push the "A" button to confirm your code.
programming.
pressing the button "B".
5 seconds to open the safe.
THE WRONG CODE
the keyboard
hand side as far as it will go.
Electronic Lock GUN
5