Publicidad
Interfaz INMBSFGL001I0xx
Configuración por Micro Interruptores
B A SG
EIA485
AC Unit
SW3 – Polarization and termination resistor
SW3
Description
1
2
3
x
x
EIA-485/RS-485 bus without termination resistor (Default value).
Internal termination resistor of 120Ω connected to EIA-485/RS-
x
x
485 bus.
x
No BUS polarization (Default value).
x
BUS polarization active.
SW1
–
Device
settings
baudrate configuration
SW1
1
2
3
4
5
6
7
8
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
NOTA: Para más información acerca de otros modos de operación de los leds consulte el manual.
NOTE: Check the manual for more information about other LED operation modes.
El Manual de Usuario está disponible en - The User's Manual is available at:
https://intesis.com/products/ac-interfaces/fujitsu-gateway/fujitsu-modbus-fj-ac-mbs-1
This marking on the product, accessories, packaging or literature (manual) indicates that the product contains electronic
parts and they must be properly disposed of by following the instructions at
Doc. r1.3
© HMS Industrial Networks S.L.U - All rights reserved
This information is subject to change without notice
SW2
SW3
SW1
and
ModBus
Description
3 FanSpeeds
4 FanSpeeds (Default value)
5 FanSpeeds
6 FanSpeeds
Not used (Default value)
Not used
Not used (Default value)
Not used
Not used (Default value)
Not used
2400 bps
4800 bps
9600 bps (default value)
19200 bps
38400 bps
57600 bps
76800 bps
115200 bps
https://intesis.com/weee-regulation
Interface INMBSFGL001I0xx
Configuration through DIP - switches
Dirección ModBus slave, escala (ºC/ºF) y magnitud (x1/x10) de
temperatura
ModBus slave address, temperature magnitude (ºC/ºF) and scale
(x1/x10)
Polarización y resistencia de terminación
Polarization and termination resistor
Configuración del dispositivo y ModBus baudrate
Device settings and ModBus baudrate configuration
SW2 - ModBus slave address, temperature
magnitude (ºC/ºF) and scale (x1/x10)
SW2
1
2
3
4
5
6
7
x
x
x
x
... (binary enumeration) ...
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
X
x
x
x
x
x
x
x
LED – Información porporcionada por los
LEDs – LED information
Comportamiento
LED
- Behaviour
Blinking
L1
0,5s ON / 0,5s OFF
(GREEN)
Flashing
0,1s ON / 1,9s OFF
Pulse
L2 (RED)
3s ON / -s OFF
Pulse
5s ON / -s OFF
L1 + L2
Alternatively
blinking
0,5s ON / 0,5s OFF
MBS slave Address /
Description
8
x
0
x
1 (Default value)
x
2
x
3
x
...
x
62
x
63
x
Temperature values in ModBus register are
represented in degrees (x1)
(default value)
Temperature values in ModBus register are
x
represented in tenths of degrees (x10)
Temperature values in ModBus register are
represented in Celsius degrees
(default value)
Temperature values in ModBus register are
represented in Fahrenheit degrees
Descripción - Description
AC Error
Communication OK
Under voltage
Device start-up
EEPROM failure
URL
https://www.intesis.com
2 / 2
Publicidad
