Publicidad
CABINET
1a
1" (2.5 cm)
1b
2
Mark (2) CATCH HOLES positions with
pencil.
Pre-drill screw holes for catch 3/8 inch
3
(0.9 cm) deep. We recommend using
a 7/64 drill bit. Be careful not to drill
through cabinet underhaul. NOTE: For
best install, take a position under the
cabinet to drill holes.
Quick tip: Mark your drill-bit with a
piece of electrical tape to correct
depth of 3/8 inch (0.9 cm).
3/8" (0.9 cm)
NOTE: If drill is too large you can use
extra force to manually tighten the
screws with screwdriver (skip steps
about pre-drilling).
4
Screw in catch by hand using a Phillips
head screwdriver.
5
Remove adhesive cover from back of
template. Slide template onto catch.
6
Close cabinet door until contact with
adhesive is made. Open door and
ensure template adhesive has stuck.
7
Mark (2) LOCK HOLES positions with
pencil. Remove template. Do not
dispose of template as you will need to
reuse it for other installations.
8
Pre-drill screw holes for lock 3/8 inch
(0.9 cm) deep. We recommend using
a 7/64 drill bit. Be careful not to drill
through cabinet door.
Quick tip: Mark your drill-bit with a
piece of electrical tape to correct
depth of 3/8 inch (0.9 cm).
9
Position lock slots centered over
pre-drilled holes. Screw in lock by hand
using a Phillips head screwdriver.
When closing door, if the lock does not
10
engage the catch, loosen screws and
adjust the lock up or down until lock
engages. Re-tighten screws.
When installation is complete, make
sure to use the magnetic key over the
cabinet to open door.
Center frame
Line up template edge A
roughly 1 inch (2.5 cm) away
from center frame (close to
door handle).
Insert template until vertical
edge meets front of cabinet
frame.
1a
1" (2.5 cm)
1b
2
Mark (2) CATCH HOLES positions with
pencil.
Pre-drill screw holes for catch 3/8 inch
3
(0.9 cm) deep. We recommend using
a 7/64 drill bit. Be careful not to drill
through drawer underhaul. NOTE: For
best install, take a position under the
cabinet to drill holes.
Quick tip: Mark your drill-bit with a
piece of electrical tape to correct
depth of 3/8 inch (0.9 cm).
3/8" (0.9 cm)
NOTE: If drill is too large you can use
extra force to manually tighten the
screws with screwdriver (skip steps
about pre-drilling).
4
Screw in catch by hand using a Phillips
head screwdriver. Put drawer back into
cabinet.
5
Remove adhesive cover from back of
template. Slide template onto catch.
6
Close drawer until contact with
adhesive is made. Open drawer and
ensure template adhesive has stuck.
7
Mark (2) LOCK HOLES positions with
pencil. Remove template.Do not
dispose of template as you will need to
reuse it for other installations.
8
Pre-drill screw holes for lock 3/8 inch
(0.9 cm) deep. We recommend using
a 7/64 drill bit. Be careful not to drill
through drawer.
Quick tip: Mark your drill-bit with a
piece of electrical tape to correct
depth of 3/8 inch (0.9 cm).
9
Position lock slots centered over
pre-drilled holes. Screw in lock by hand
using a Phillips head screwdriver.
When closing drawer, if the lock does
10
not engage the catch, loosen screws
and adjust the lock up or down until
lock engages. Re-tighten screws.
When installation is complete, make
sure to use the magnetic key over the
drawer to open drawer.
DRAWER
NOTE: Remove drawer if
possible for easier installation.
Line up template edge A
roughly 1 inch (2.5 cm) away
from side of drawer.
Insert template until vertical
edge meets front of cabinet
frame.
Publicidad
