Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH
TROUBLESHOOTING / STORAGE / MAINTENANCE
E
, i-Light Device Maintenance
F CAUTION: Before performing maintenance on your i-Light device, ensure that the power switch is OFF
and the power cord is disconnected from the base unit.
, Replacing the Bulb
1. Press the treatment head release buttons and gently pull to remove the treatment head.
2. Gently pull out the old bulb cartridge.
3. Replace with a new bulb cartridge.
F CAUTION: When replacing the bulb cartridge, do not touch the flash bulbs directly as this leaves oils and
residue. Doing so could reduce the effectiveness of the bulbs or cause them to crack during treatment.
4. Replace the treatment head, making sure it snaps into place.
, Storage
• Switch off the unit, unplug it and let it cool down for 10 minutes before storage.
• Store the unit in a dry place at a temperature between 15º C and 35º C.
, Troubleshooting
Always read these instructions fully before using i-Light. Refer to this troubleshooting guide if you
experience any problems with i-Light, as this section addresses the most common problems you could
encounter with i-Light. If you have followed the instructions in this section and continue to experience
problems, please contact the Remington® Service Centre for further assistance.
The power switch is ON, but the unit is not working.
• Make sure the unit is plugged into a working electrical outlet.
• Try switching to a different outlet.
The unit appears to have cracks or is broken.
Do not use if the unit is damaged. If you have concerns about using the unit, discontinue use and contact
the Remington® Service Centre for further assistance.
, Frequently Asked Questions
I have switched the unit ON, but I cannot increase or decrease the energy level.
• Try resetting the unit by turning it off and waiting several seconds before turning it back on.
The Bulb Status Indicator Light turns green but the unit does not flash when the button
is pressed.
• Make sure the Skin Contact Sensor is in full contact with the skin.
• Try resetting the unit by turning it off and waiting several seconds before turning it back on.
There is a strange smell.
• Be sure the area is completely shaved before treatment.
The treated areas become red after treatment.
• This is normal and the redness should subside. If not, try using a lower energy level.
14
ENGLISH
I have not seen optimal results or hair has begun to grow back.
• Hair may begin to grow back after your initial treatment. This is perfectly normal. For optimal results,
repeat the treatment when you notice hair regrowth.
Note: Do not treat the same area more than once a week.
F BE AWARE: If the unit is used over an extended period of time, the unit might
automatically disable momentarily (estimated 40 seconds) to cool down. Once the unit has cooled down,
it will be ready to use again.
Intensity/Flash Mode LED
All currently selected LEDs flashing
Intensity LEDs flashing in sequence
All LEDs flashing with warning beep
Audible Tones
Not Full Contact
Replace Light Cartridge
Contact Sensors Stuck
, Frequently Asked Questions (www.remington-ilight.com)
Q. What is i-Light? What is Intense Pulse Light (IPL)?
A. IPL works by directing an extremely short, intense pulse of filtered light into the skin. The light is
absorbed by the coloured pigments in and surrounding the hair and disables the hair follicle
temporarily, preventing hair regrowth.
Q. Who can use i-Light?
A. Both men and women can use i-Light to remove unwanted hair anywhere below the neck, and
females can use to treat facial hair below the cheekbone. i-Light has been designed for individuals with
light to medium skin tones and dark hair. Safe skin tones include white, ivory, tan, beige and light
brown only. Safe natural hair colours include black, dark brown and medium brown.
Q. What areas of my body can I treat with i-Light?
A. i-Light is designed for unisex use on areas below the neck, including the legs, underarms, bikini line,
arms, chest and back. Females can also use on facial hair below the cheekbone.
Q. What can I expect from i-Light?
A. i-Light provides safe and effective salon-grade hair removal using IPL technology.
Indication
Unit is overheated and is disabled momentarily to
cool down.
Unit is malfunctioning. Turn the unit off, wait a few
moments and try again. If problem persists, the
unit should be returned for repair.
Treatment head is removed or loose.
Indication
Flash button was pressed while the skin contact
sensor was not fully engaged.
Light cartridge is missing or needs to be replaced.
Flash button was pressed after the contact sensor
had been engaged since unit start up. Contact
sensor may be stuck.
15
Publicidad
