Página 1
Large & Extra Large Fixed Flat Panel Mount REDLFHD120P REDXLFHD175P INSTRUCTION MANUAL MANUAL DE INSTRUCCIONES MANUEL D’INSTRUCTIONS CAUTION: CAUTION: DO NOT EXCEED MAXIMUM THE MAXIMUM LOADING WEIGHT IS 120 LISTED WEIGHT CAPACITY. SERIOUS LBS FOR LARGE MOUNT AND 175LBS FOR EXTRA LARGE INJURY OR PROPERTY DAMAGE MAY MOUNT.
Página 2
QUESTIONS? NEED HELP? PLEASE CALL info@redatomproducts.com DISCLAIMER – WARNING INFORMATION Disclaimer –. RED ATOM has extended every effort to ensure to accuracy and completeness of this manual. However, RED ATOM does not claim that the information covers all installation and or operational variables. The information contained in this document is subject to change without notice or obligation of any kind. Regarding the information contained herein, RED ATOM makes no representation of warranty, expressed or implied, and assumes no responsibility for accuracy, sufficiency, or completeness of the information contained in this document.
Página 3
HARDWARE PRODUCT NUMBERS M4 x 12 M5 x 12 M6 x 15 M8 x 15 M4 x 25 M5 x 25 M6 x 25 M8 x 25 SQUARE WASHER SPACER STEEL WASHER STEEL WASHER 8 mm LAG ANCHOR BOLT PRODUCT COMPONENT PARTS Flat Panel Mounting Pattern (W X H) Minimum: 100mm x 100mm (Large and Extra Large) Maximum: 400mm x 400mm (Large)
Página 4
STEP 1A - FLAT BACK FLAT PANEL (UNIVERSAL VERTICAL RAILS) Connect Universal Vertical Rails to flat panel Conecte el adaptador al monitor Connectez l'adaptateur au moniteur STEP 1B - CURVED BACK FLAT PANEL (UNIVERSAL VERTICAL RAILS) Connect Universal Vertical Rails to flat panel Spacers can also be used to Conecte el adaptador al monitor provide clearance for cables...
Página 5
STEP 1C - USE M8 STEEL WASHER IF THE PHILLIPS SCREWS FROM THE MONITOR KIT ARE TOO LONG Diagrams show three options for using additional washers if hardware screws are too long to properly tighten into back of flat panel television.
Página 6
STEP 2 - WOOD STUD INSTALLATION (CONCRETE INSTALLATION SKIP TO STEP 3) STEP 2- CENTER UNIVERSAL MONITOR PLATE Find stud and mark edge and center locations Ubique el panel y marque las ubicaciones de los bordes y el centro. Repérez l'emplacement d'une poutre, puis marquez l'emplacement des bords et du centre de cette poutre. LEVEL WALL PLATE WITH INCLUDED BUBBLE LEVEL AND...
Página 7
STEP 2C - MOUNT WALL PLATE TO WALL Mount wall plate Coloque la placa de pared Montez la plaque murale 16” STUD (Large Fixed Mount) 16” or 24” STUD (Extra Large Fixed Mount)
Página 8
STEP 3 - SOLID CONCRETE INSTALLATION Use wall plate to mark mounting locations/drill pilot holes Use la placa de pared para marcar el lugar donde se realizará la instalación Utilisez la plaque murale pour marquer l'emplacement de montage Level Solid Concrete Drill Bit Drill Pilot Hole DRILL BIT...
Página 9
STEP 3C - SOLID CONCRETE INSTALLATION. Mount wall plate Coloque la placa de pared Montez la plaque murale Insert wall anchors gently into concrete wall with hammer if necessary Hammer STEP 4A - ATTACH PANELTO WALL PLATE & ADJUST TILT ANGLE Hang Vertical Rails with monitor attached Cuelgue con el monitor adherido.
Página 10
STEP 4B - ADJUST THE SCREWS ON THE VERTICAL RAILS TO LEVEL THE FLAT PANEL Maximum leveling adjustment 0.5”...
Página 11
STEP 4C - ADDITIONAL SECURITY FEAUTURE (OPTIONAL) Option Opcione Option Vertical Rails Flat Panel Wall Plate Vertical Rails have 7mm hole located at the bottom for placement of pad lock for additional theft security (pad lock not included)
WARRANTY INFORMATION This warranty applies to US Residents who purchase from an authorized RED ATOM Dealer. RED ATOM products are covered against defects in materials and workmanship for 5 years. RED ATOM will repair or replace the defective component or product, at its sole discretion. Failure to follow product care instructions from RED ATOM will result in void of warranty.