Sharp DR-S460 Guia De Inicio Rapido página 3

ENGLISH
Before using your product, read all safety instructions. For full instructions
please refer to the user guide available to download from the website www.
sharpconsumer.eu.
Panels & Controls
-1. Front Panel
1. MODE – Press to select the modes: DAB/DAB+, FM, Bluetooth, AUX IN.
2. STANDBY – Press this to turn on the unit or enter Standby mode.
3. INFO/MENU – Press to view the station information, or enter main
menu setting screen.
4. ENTER – Press to confi rm a selection.
PREVIOUS ◄ – Press to go back to the last selection, or decrease the
5.
frequency, or seek the last strongest station.
NEXT ► – Press to go forward to the next selection, or increase the
6.
frequency, or seek the next
7. SCAN – Use to scan the radio stations, or to adjust the backlight level.
8. PRESET – Press to recall the preset stations.
9. DISPLAY SCREEN – To show the information.
-2. Rear Panel
10. VOLUME+/- knob – Turn to adjust the volume level.
11. FM Antenna – To receive the FM signal.
12. DC Power Input – DC 12V
13. AUX IN jack – Connect the 3.5mm audio cable to this jack to enjoy the
external audio music.
General Operating Instructions
Mains Adaptor (supplied with the package)
Connect the mains adaptor to the DC power socket on the rear panel of
the radio.
Turn On the Radio
Press the STANDBY button to turn on the radio.
Switch to Standby Mode
When in use, long press the STANDBY button to enter Standby mode.
Press it again to wake up the radio.
The fi rst time the radio is used
The fi rst time you turn the radio on it will automatically scan for stations.
Snooze function
When the alarm is sounding in Standby mode, rotate the Volume Knob to
activate the SNOOZE function.
Time Auto Update
The time and date can be updated automatically if the system detects the
RDS signal. If the RDS signal is weak or cannot be detected, the time will
not automatically update.
Main Menu Setting
Long press the INFO/MENU button to enter the main menu setup screen.
Find and enter the <System> screen by pressing the ENTER button.
Then use the ◄/► button to cycle through the menu options: <Time
setup>, <Alarms>, <Sleep>, <Language>, <Prune>, <Station Order>,
<Backlight>, <Factory reset>, <SW version>.
NOTE: The <Prune> and < Station Order> are only available in DAB mode.
Select one of the options and then press the ENTER button to access that
menu.
Alarms
When the <Alarms> appears,
1. Press ENTER button to enter the alarm setting screen.
2. Choose <Alarm 1: off > or <Alarm 2: off >, press the ENTER button to
set the alarm On.
3. Using the ◄/► button to select the alarm time, press ENTER to
confi rm.
4. Select the alarm days: Daily, Once, Weekdays, Weekends.
5. Set the alarm mode: DAB, FM, Buzzer.
6. Set the alarm volume: there is a slide bar adjusting the alarm volume,
press ◄/► button to increase or decrease the volume level, press
ENTER button to confi rm.
7. After all the above settings, enter the Save screen, press ENTER button
to save the alarm.
8. To cancel the alarms, enter the alarm setting screen, press ENTER
button to select Off and then enter save screen to save the alarm off
setting.
DAB/DAB+ Operations
Scan Stations
When turning on to DAB/DAB+ mode, the radio will automatically scan the
stations it found in this area.
Press the ◄/► button to select the previous or next stations, then press
the ENTER button to activate to play the station.
Station Tuning
Long press the INFO/MENU button, when the <Station scan> appears,
press the ENTER button, then use the ◄/► button to cycle through the
scanning options: <Full scan>, <Manual tune>.
1. Select the <Full scan>, and then press ENTER button to enable full
scanning.
2. Select the <Manual tune> and press ENTER button, use ◄/► button
to select stations from 5A:174.928MHz to 13F:239.200MHz. Then
press ENTER button to activate the selected station.
FM Operations
Switch to FM mode by pressing the MODE button.
Select Stations
To search for an FM station from 87.5 to 108.00MHz.
1. Press the ◄ or ► button to skip to go back or go forward the
frequency by the step of 0.05MHz.
2. Long press the ◄ or ► button to skip to the previous or next station
of the strongest reception. Once a station has been found, it stops
scanning automatically. If no station is found, it will stop after it has
cycled through the entire frequency.
Tuning Stations
1. Long press the SCAN button to scan the stations. During scanning, the
screen will display a slide bar that indicate the progress of the scan and
the amount of radio stations that have been found so far. Once the scan
has fi nished, the radio will play the fi rst station it found.
Store Stations
It is possible to store up to 10 of your favourite FM/DAB stations. This will
enable you to access your favourite stations quickly & easily.
1. To store a preset, you must fi rst be listening to the station you would
like to save.
2. Press the PRESET button.
3. Use the ◄/► button to select desired preset number 1-10.
4. Press and hold the ENTER button to confi rm.
1