natec KANGAROO DUAL Guia De Inicio Rapido página 2

For your safety and the satisfaction of using this product,
please read this manual carefully before installation.
FEATURES:
• Supports super speed USB 3.0 up to 5Gbps
• Supports 2.5''&3.5''SATA I/II/III HDD or SSD
• Supports capacity 2x4 TB or above
• Supports One Touch Backup or Duplicate
• Supports plug & play
• Powered AC 100~240 V 50~60 Hz 0.8 A
DC 12V2.5 A
CAUTION!
Please wear ground bracelet or touch metal
faucet to release static electricity as the external
enclosure' s PCB is very sensitive to static
discharges.
Note: Images are for example only. Actual
positions of switches or connectors and pieces
may vary depending on the model.
DUPLICATOR (CLONE) MODE
Note! The Duplicator Mode only works when the docking station is NOT
connected to a PC via the USB cable.
For clone function, you need two hard drives:
• Source Disk: drive with the data you want to duplicate (clone).
• Target Disk: in which you want to store the data of the source disk.
Attention: The capacity of the target disk should be equal or larger than the
source disk.
Caution! All data on your Target HD will be lost. If you have important data on the
HD, please back up the data before beginning the Clone operation.
1. Make sure that those hard drives have no bad sectors. Bad sectors will
cause unpredictable problems.
2. Put the Source Disk into the A bay, then put the Target Disk into the B bay.
3. Please make sure that those hard drives are correctly and firmly
connected to those SATA connectors of the docking station.
4. Connect the power adapter to the docking station and power outlet.
5. Press the power button to power up the docking station.
6. Wait at least 10s till the docking station is prepared.
7. Keep pressing the Clone button for 3 seconds to begin duplication.
• During the Clone process, those LED indicators will flash to show the
percentage of the progress.
• Begin Clone process: four LED flash one by one.
• One LED stays solid:25%
• Two LED stays solid:50%
• Three LED stays solid:75%
• Four LED stays solid:100%
• When the four LED all stay solid, the process of the Clone had been
finished.
8. When the process of the Clone is finished, please press the power button
to turn off the docking station. Please take out those hard drives carefully
because they may be very hot.
NOTE!
• Those hard drives may become hot during the Clone process.
• The Clone process may take various hours to finish.
• Those hard drives may produce noise during the Clone process.
• A Cloned drive also takes over the disk ID from the master drive. This causes
Windows Vista,Win7/8 to shut down one of the drives if both drives are placed
into the HDD docking after cloning. The disk can be switched "online" again in
the Windows option "Disk Management".
PACKAGE CONTENTS:
• HDD Docking Station
• USB 3.0 cable
• User's manual
• Power adapter (12 V/2.5 A)
HDD-A (Source)
HDD-B (Target)
DEVICE MODE
The device mode permits the docking station to act as external dual hard drives
that allows you to backup the data of your computer to those external hard drives.
1. Make sure that those hard drives have no bad sectors. Bad sectors will
cause unpredictable problems.
2. Put one or two hard drives into the docking station. Please make sure
that those hard drives are correctly and firmly connected to those SATA
connectors of the docking station.
3. Connect the USB cable to the docking station and to a PC.
4. Connect the power adapter to the docking station and to power outlet.
5. Power up the docking station by pressing the power button.
6. Now the computer should detect the new hardware.
OTB FUNCTION (ONE TOUCH BACKUP)
The OTB function lets you backup your data by just pressing one button. It' s an
easy way to backup your important data to an external hard drive.
For more information, please visit our website (www.natec-zone.com) to
download the file about OTB introduction and operate software.
IMPORTANT!
Always keep a backup copy of files from your hard drive connected to enclosure.
Manufacturer does not take responsibility for damages resulting from lost data
due to wrong operation or malfunction of the product, the software, personal
computers or peripheral devices. The manufacturer is not liable for damage
resulting from misuse of the docking station.
• Product covered with 24-month warranty.
• The safe product, conforming to the EU requirements.
• The product is made in accordance with RoHS European standard. The
standard was issued in order to decrease the amount of the electronic and
electrical waste emitted into the atmosphere.
• The WEEE symbol (the crossed-out wheeled bin) using indicates that
this product in not home waste. Appropriate waste management aids in
avoiding consequences which are harmful for people and environment and
result from dangerous materials used in the device, as well as improper
storage and processing. Segregated household waste collection aids
recycle materials and components of which the device was made. In order
to get detailed information about recycling this product please contact
your retailer or a local authority.
• For more information visit www.natec-zone.com
SYSTEM REQUIREMENTS
• USB 3.0 port
• Windows 2000/XP/Vista/Win7/Win8/Win
10 (No driver installation needed)
• Mac OS 10.X or above
• OTB function does not work under
Windows 98 and Mac.
Clone button
EN