Power On/Off; Manual Operation; Automatic Operation - Schwaiger 658002 Manual De Instrucciones

USER GUIDE
OPERATION IN DETAIL:
The correct way to place the device
Always place the air purifier
sure that the device cannot fall down and that the power cord
may only be plugged into suitable wall sockets.
If you use the device in the same place for a longer period of time, make sure that you also clean the walls and floors in
the vicinity, as dirt can collect here. Always ensure that there is sufficient distance to walls, furniture, or other electrical
devices during operation.
If you want to use the device specifically for filtering dust or pollen, it is recommended to place the device preferably near
the floor, since dust and pollen are heavier particles that are mostly suspended in the air near the ground.
To ensure that the air can circulate effectively in the room, the air outlet
furniture or walls.
Air quality measurement sensor
The device has a built-in sensor
fine dust particles with an aerodynamic diameter < 2.5 µm) in the air is measured. Depending on the air pollution, the
illuminated lamp ring
8
Blue: PM 2.5 < 80 µg/m³ (low air pollution)
Yellow: PM 2.5 80 – 150 µg/m³ (medium air pollution)
Red: PM 2.5 >150 µg/m³ (increased air pollution)
It is recommended to increase the speed of the built-in fan in case of increased or medium air pollution.
ATTENTION!
The air purifier is not a substitute for regular ventilation of the windows in the room!
The air purifier cannot detect dust, ticks and their feces, mold spores, pollen, bacteria, or viruses, but only the general
concentration of particles in the air.
Air conditioners and radiators can affect the sensor's measurement accuracy if the device is placed near them.

Power on/off

Switch on the device by pressing the On/Off button
ton lights up blue. The unit is now ready for operation and is preset to run at the medium speed level. During operation,
air is sucked in through the air inlet
through the air outlet
6
Press the On/Off button
on the product will go out.

Manual operation

Switch on the unit as described above. On the control panel
of the Fan speed indicator
tion, the measurement of the air quality in the room is complete and, depending on the air pollution, the illuminated lamp
ring lights up either blue, yellow or red. Press the Fan speed button
8

Automatic operation

Switch on the device as described above. Then press the Auto-mode button
After approx. 2 minutes of operation, the measurement of the air quality in the room is complete and, depending on
the air pollution, the illuminated lamp ring
detected, the air purifier will adjust the speed of the built-in fan and automatically increases or decreases for optimal air
flow. Press the Auto-mode button
Setting up the speed
If you are in manual mode, you can adjust the speed of the fan yourself at any time by pressing the Fan speed button
until the desired speed (low - medium - high) is reached.
18
Furthermore, the device has an additional speed level (Turbo), which can be set separately. To do so, press the Turbo
button to reach the maximum speed of the fan. The Turbo button then lights up red.
16
To end the maximum speed of the fan again, either press the Turbo button
tively, you can also press the Sleep-mode button
If you do not manually switch off the maximum speed, it will automatically end after 1 hour of operation. The Turbo
button then no longer lights up red and the device then runs at medium speed again.
16
on an easily accessible, level, dry, heat-resistant, and sufficiently stable surface. Make
1
for measuring the current air quality in the room. The PM 2.5 concentration (respirable
9
lights up in a different color:
, conveyed through the filter
5
.
again to switch the unit off. You will hear again a short confirmation tone here and all lights
17
light up blue. The unit is now in manual operating mode. After approx. 2 minutes of opera-
19
lights up either blue, yellow or red. Depending on the level of air pollution
8
again to stop automatic operation.
13
cannot become a tripping hazard. The power plug
10
once. You will hear a short confirmation tone and the On/Off but-
17
, cleaned, and then blown out of the unit again
2
, both the illuminated lamp ring
7
18
to reduce the fan speed and directly enter Sleep mode.
15
12
should always be at least 30 cm away from
6
8
to set the desired speed of the built-in fan.
to switch to automatic operation mode.
13
again or the Fan speed button
16
11
and the medium level
. Alterna-
18