Publicidad
Idiomas disponibles
Idiomas disponibles
1)
Make sure the LED lights are directed away from your eyes then move the power
switch to the "ON" position.
2)
Among all the lights, select one as the parent light (PL), and the others as the
children lights (CL).
3) (CL): Move the link button (Part E) to the "LINK ON" position (direction of arrow) on all
children lights (CL) you want to connect to the parent light (PL). Keep in the "LINK ON"
position for one second, then switch the link button (Part E) back to its initial
position quickly. The (CL) will start ashing every second, now they are in link mode.
All (CL) after complete step 3) operation, time to place the (PL) in link mode.
4) (PL): Move the link button (Part E) to the "LINK ON" position (direction of arrow). Keep
in the "LINK ON" position for 5 seconds, then the parent light (PL) will ash very slowly
( ashing every 4 seconds). The (PL) is now in link mode and sending signals to pair
with the selected (CL).
5) Once the (CL) in link mode receives and saves the paired ID code signal transmitted
by the (PL), completes and exits the pairing mode. The blinking light(s) will stop
ashing and resumes normal use. Make sure that all (CL) pairs are completed.
6) (PL): Move the link button (Part E) for parent light (PL) back to its initial position.
The blinking light(s) will stop ashing and resumes normal use. Now the (PL)
is linked with the (CL), the linking process is complete. When any of the lights (PL)
or (CL) are triggered by motion, all lights will activate.
Note: Light will stay on 30 seconds when triggered by motion. Detection range is 19.69-26.2 ft (6-8m), detection angle is 120°. Light use radio
frequency technology to link, and should not be greater than 49.2 ft (15m) between the neighboring/adjacent lights.
If you buy a new linkable solar light and want to add it into the "family" , you can re-start this LINKABLE SET-UP INSTRUCTION again for all
the lights you want to link.
If you want one of the (CL) to unpair, turn link button (Part E) to the "LINK ON" position (direction of arrow), stay for more than 5 seconds, the (CL)
will ash very slowly ( ashing every 4 seconds). then turn back to the original position. Then this (CL) is unpaired.
Precautions:
1: The luminaries that are paired with the code are not completed in the normal steps. After the power is turned off, the power is turned on
again to resume normal operation.
2: The code switch is mis-operated when the code is not being used. It needs to be powered off again and then powered back on to resume
normal operation.
FCC WARNING
Warning: Changes or modi cations to this unit not expressly approved by the party responsible for compliance could void the user authority to
operate the equipment.
Notes: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to protection against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency enerqy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no quarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio / TV technician for help.
WARNING:
Do not dispose of lithium batteries in municipal waste stream or by re as batteries may explode. Do not open, short circuit, or destroy
batteries. Dispose of batteries in accordance with Local, State, and Federal regulations. Do not mix old and new batteries. Do not mix alkaline,
standard (carbon-zinc), or rechargeable (nickel cadmium, nickel metal hydride or lithium ion) batteries .
©
Wal-Mart Stores, Inc.
Hyper Tough is a registered trademark of
Wal-Mart Stores, Inc. All Rights Reserved.
Distributed by/Distribuido por
Wal-Mart Stores, Inc.,
Bentonville, AR
MADE IN COUNTRY/HECHO EN COUNTRY
TM
LINKABLE SET-UP INSTRUCTIONS
For assistance with assembly or instruction, parts and customer service, call: U.S.A. & Canada only: 1-844-551-0680
8am – 5pm Monday – Friday, Central Standard Time Or email: Customerservice@qx-usa.com
LINKABLE SOLAR LED PATHWAY LIGHT
ITEM: Q01DA0442-08
(E) Link on button
(D) Power switch
10/22/2019
2/2E
Publicidad
