Porter Cable 75301 Manual Del Usuario

For your own safety, read your router's instruction manual before using
any accessory. Failure to heed these warnings may result in personal injury and serious
damage to the router and the accessory. When servicing this tool, use only identical
replacement parts.
To reduce the risk of injury, turn unit off and disconnect it from power source
before installing and removing accessories, before adjusting or when making repairs. An
accidental start-up can cause injury.
To use the 75301 Height Adjuster with a router mounted in a table, there needs to be a
hole (or holes) in the table for the Adjuster to reach the router.
IMPORTANT: The instructions below are for some specifi c situations where holes
NEED TO BE DRILLED. Check your table to see if holes are already provided to
allow the Adjuster clearance.
If you are not using a Porter-Cable router table, your router's sub-base (S) Fig. 2 can be
used as a template to determine where holes need to be drilled. Use the instructions be-
low as a general guide on how to attach the Adjuster for a non-Porter-Cable table.
DISCONNECT ROUTER FROM POWER SOURCE BEFORE
ASSEMBLING THE HEIGHT ADJUSTER.
WHEN USING WITH THE 698 ROUTER TABLE
AND THE 890 SERIES ROUTERS:
1. Make sure router is not attached to the table. Remove the router's plastic sub-base
(an example of one type used with the 890 router is shown in Fig. 3).
2. Flip the table over with the fence side on top, as in Fig. 4. Then, with the smooth
side of the sub-base against the bottom of the table, line up the three holes (A)
Fig. 3 in the sub-base with the three holes (C) Fig. 4 in the table. Make sure holes (B)
Fig. 3 are on the bottom when the three holes (A) and (C) are aligned.
3. Use the screws supplied with the table to hold the sub-base in place. Looking straight
down on holes (B) Fig. 3, center punch or mark a spot in the table in the center of
these holes (B).
4. Before you drill the holes, be sure the table is arranged so nothing below
it will be damaged during drilling.
5. Move the sub-base. At your marks, drill a 7/16" hole. Approximate location of the
holes for the 890 Series is represented by the dotted white circles in Fig. 4.
6. Turn table over and attach router as described in the owner's manual.
7. Insert Height Adjuster so the index ring (R) rests on the table top (as shown in Fig. 1)
and the adjusting arm's hex opening matches the hex screw in the router.
WHEN USED WITH THE 698 ROUTER TABLE
AND THE 8529 PLUNGE ROUTER:
1. Make sure router is not attached to the table. Remove the router's plastic sub-base
(shown in Fig. 5).
2. Flip the table over with the fence side on top, as in Fig. 4. Then, with the smooth
side of the sub-base against the bottom of the table, line up the three holes (D)
Fig. 5 in the sub-base with the three holes (C) Fig. 4 in the table. Make sure hole (E)
Fig. 5 is on the bottom right when the three holes (D) and (C) are aligned.
3. Use the screws supplied with the table to hold the sub-base in place. Looking straight
down on hole (E) Fig. 5, center punch or mark a spot in the table in the center of hole
(E).
4. Before you drill the hole, be sure the table is arranged so nothing below
it will be damaged during drilling.
5. Move the sub-base. At your mark, drill a 7/16" hole. Approximate location of the hole
for the 8529 is represented by the dotted white circle in Fig. 4.
6. Turn table over and attach router as described in the table's manual.
7. Insert Height Adjuster so the index ring (R) rests on the table top (as shown in Fig. 1)
and the adjusting arm's hex opening matches the hex screw in the router.
ESPAÑOL en revés / FRANÇAIS sur l'inverse
Porter-Cable, 4825 Hwy. 45 North, Jackson TN 38305
www.deltaportercable.com
Height Adjuster Model 75301
(888) 848-5175
A23842 - 07-16-07
R
S
890 series
8529
A
B
Router Table Fence Side
C
890 series
Fig. 1
Fig. 2
Fig. 3
8529
Fig. 4
E
Fig. 5