Aetaire AIR160 Manual De Instrucciones página 5

Properties of the AIR 160:
• Suitable for areas up to 100 m
• Adjustable to 25 m or 50 m
3
• Lamp replacement once each operational year
• Filter replacement each 3-6 months
• The unit indicates when the lamp should be replaced
• Up to 50% more UV-C yield as a result of reflection in the
aluminium housing
• Simple installation and maintenance
• Stand-alone system and immediately ready-for-use
through "plug and play"
• 2-year guarantee on manufacturing faults
The AIR 160 is effective against:
• Viruses • Bacteria
• House-dust mites • Dust and particulates • Pollen
• Cigarette smoke • Harmful gases
The AIR 160 is recommended for the following areas:
• Schools • Day-care centres
• Nursing homes • Hotels
• Copying areas • Doctor's surgeries • Dental surgeries
• Veterinaries • Animal shelters
• Lounges • Bedrooms
• Computer rooms • Studies
• Holiday homes • Caravans
• Fitness areas • Smoking areas
• Hairdressers • Beauty parlours
• Pubs • Meeting rooms
Safety
This device produces harmful radiation. Direct contact could impair the
eyes and skin. Only check the operation of the UV-C lamp through
the air vents at the top of the unit. The openings will light up blue if
the lamp is on.
• When switching on the device for the first time, you may notice
a burning smell from the UV-C lamp for a short time. This odour
is similar to the odour you notice when using a sun bed, and will
disappear after a short time.
• Always comply with the electricity company's regulations with
regard to any permanent connection to the mains. If there is any
doubt regarding the connection, consult a recognized electrician
or the electricity company. Always work with an earth leakage
current circuit-breaker (residual current trip).
• Always remove the plug from the socket before carrying out any
maintenance or repair work on the unit. Never insert the plug /
pull the plug from the socket when you are standing in water or
if your hands are wet.
• Never submerge this device in water.
• Never install the unit in an area subject to full sunlight.
• Keep children away from this device and from the cable.
• The cable of the device cannot be replaced. The complete unit
must be replaced if there is any damage to the power cable.
Never remove the plug, but always leave the electrical unit
intact. An electrical unit with the plug removed will no longer be
covered by the guarantee.
• Once the device has been switched off, the lamp will remain hot
for approximately 10 minutes.
• Do not use the device if any of the components are damaged.
• This product can only be used according to the guidelines
described in these instructions for use.
3
air per hour
3
• Moulds
• Odours
• Old people's homes
• Offices
• Kennels
• Hobby rooms
• Play rooms
• Boats
• Restaurants
• Public toilets
• Dressing rooms
Installation of the device
Determine where the device will be installed. When selecting a
location for the device, please bear in mind that the unit must
be able to circulate the air in the room freely and without
obstructions. Also ensure that there is a power socket near the
selected location.
Install the device in a dry place. Ideally, the unit should be mounted
in the vertical position, with a free space of at least 50 cm
underneath for carrying out maintenance and for the replacement
of the filter and/or UV lamp.
1. Remove the clips (A) (see Drawing 2) from the AIR160 by
unscrewing the cover (M) (see drawing 5) and position the clips
(A) at the selected location so that you can mark where the
clips should be fitted onto the solid back wall.
2. Fix the clips at the selected location with suitable screws and/or
plugs (see Drawing 2).
3. Place the AIR 160 in the fixed clips in the hinge and place the
brackets into its place (see Drawing 3, 4). Finally screw the cover
on the clips (see drawing 5).
4. Insert the plug into the socket and check the operation of the
UV-C lamp (H) - only do this through the air vents at the top
of the unit! Blue light can be seen through the air vents of the lid
(I) if the lamp is on (see Drawing 1).
5. Check the operation of the ventilator (K) by holding your
hand underneath the filter grid (C). If you feel an air flow, the
ventilator (K) is working (see Drawing 1).
Key
press briefly
press for 3 sec.
5
sec
wait 5 sec.
selection confirmed
lamp operating time
real-time clock
test
air circulation, low position
air circulation, high position
set clock
reset
fail